查询词典 slide guide

According to the characteristics and construction requirements, to develop the basis of elevation from the beginning of silo slipform construction used, sliding up to 4.3 meters above sea level, the reinforced air slide 5.15 meters; Party to begin construction within the building and the warehouse floor, after the completion of sliding mode Then slide up to 26 meters warehouse roof, sliding mode to remove.

根据工程特点及工期要求，拟定筒仓从基础标高开始采用滑模施工，滑升至标高4.3米时，加固空滑到5.15米；甲方开始施工仓内建筑及库底板，完工后滑模接着滑升至仓顶26米，滑模拆除。

Main job is to guarantee the scraping interaction and equipment on both sides of the friction surface or can obtain higher precision and accuracy, precision and shape accuracy, precision and contact transmission because of good lubrication, manual and repeatedly is worthy, large amounts of wind, time-consuming, scraping the time needed for different devices vary, such as boring slider and slide block wind profiling, between the match before measuring clearance between the original value, and then according to the technical requirement to measure the value of time and scraping scraping, then apply DanFen red on the slider, manual let slip on the slide seat back and forth, they do straight-line movement between full contact and friction, reoccupy scraper scraping friction creates the contact point, so repeatedly, until the technical requirements for the match, single within 2 days, must blow to the boring if all the time to work with wind, a half month is required.

刮削过程。刮削工作主要是为了保证设备相互接触并摩擦的两面间能获得较高的尺寸精度、形状精度、位置精度、接触精度、传动精度和良好的润滑，因是手工操作且需反复配刮，故工作量大，耗时较长，设备不同，刮削所需时间也各不相同，例如镗床上滑座与下滑座间的配刮，刮削前先测量出二者之间原有的间隙值，然后根据工艺要求测算出需刮削值及每次的刮削量，再将红丹粉涂于上滑座之上，手工让上滑座在下滑座上来回做直线运动，使它们之间充分接触和摩擦，再用刮刀刮削摩擦产生出的接触点，如此反复多次，直至技术要求范围之内，单此项配刮需2天左右，若对于整个镗床所有配刮工作的时间总和，则需半个月左右。

You can work with slides in the Slide Sorter view just as you can in the Slide pane.

在幻灯片浏览视图中，可以像在幻灯片窗格中一样，对幻灯片进行操作。

The same phenomena occurred with the distal end displacements when horizontally loaded: the largest was seen with the dovetail slide beyeler, followed sequentially by the Spang Stabilex, CCT, cylindrical slide, and the Mini SG.

结果显示各组之间虽然存在有许多统计意义差别，然而垂直施力时近心及远心的位移都很小(近心小於 3.0 micrometers，远心小於 21.4 micrometers)。

Slide your left foot out of the stirrup and simply slide down until your feet touch the ground.

幻灯片您的左脚出於对箍筋和简单地滑下，直到您的脚触及地面。

Anti-slide pile is an important method for slope treatment,especially when the slide face is certain and the subterrane is stable,the method is proved to be prior.

1引言 抗滑桩目前被广泛应用于边坡加固工程[1～6]，特别当边坡滑动面确定，滑动面下覆地层强度较好时，更能体现它的优越性。

To find some useful eigenvalue in time series by mining the distributing values of original series, and deduce a collection of candidate slide-window size, find the optimal slide window size by adapting to the series eigenvalue variable motion movement.

通过对时序特征值分布函数挖掘，发现时间序列中的有效特征点，进而确定一组合适的滑动窗口宽度；最后根据序列的变化情况来决定最优的滑动窗口宽度，对原数据维度进行简约。

As special window sash slide rails for plastic-steel sliding doors and windows, CHUANGYOU aluminum-alloy slide rails are made to specified sizes through die extrusion from aluminum ingots on hot rolling equipment and oxidized on the surface for corrosion protection.

窗友铝滑轨均采用优质铝锭，由热压延设备经模具挤出成各种规格，经表面防腐氧化处理后的塑钢推拉门窗专用窗框滑轨。

The slide master associated to the slide currently in the workarea.

与当前工作区中幻灯片相关的幻灯片母版。

On the base of the abave analysis,the first reinforce scheme is anti-slide pile to reinforceslope.Design and calculate anti-slide pile on theory of elasticity pile and rigidity pile.

针对上述计算分析的结果，提出边坡加固方案一：抗滑桩加固边坡分别按弹性桩和刚性桩对抗滑桩进行了设计计算。

Metrorrhagia is also gynaecological problems of common diseases.

崩漏是妇科常见病也是疑难症。

WordFTP gives you the convenience and timesaving you need.

wordftp让您的方便和省时您所需要的。