查询词典 sleeve

Aiming at the two structural features of axle shaft sleeve on the basis of analyzing various forming technologies applied in domestic and overseas in recent years,two new hot extrusion forming technology of axle shaft sleeve are worked out.

针对半轴套管的两种结构特点，在分析了国内外近年来所采用的各种成形工艺的基础上，分别开发了用镦粗-反挤压和扩径-正挤压两道复合工序相结合成形分体式半轴套管和用两次复合镦挤的方法成形整体式半轴套管的两种热挤压成形新工艺，通过物理模拟实验证明了成形工艺的可行性、实用性。

Experimental research of forming process for axle shaft sleeve with flange far from big end;2. Applying software DEFORM,the forming process has been analyzed for axle shaft sleeve .

应用DEFORM软件对半轴套管成形过程进行数值模拟，分析了金属在成形过程中各种场量的变化，对不同成形方案金属流动情况进行了预测，确定了最优的成形工艺和合理的模具结构。

By chosing the material of axle sleeve with high strength and decreasing the length of contact face for axle sleeve and axle neck, the lubrication condition of frictional pairs was improved, and the wear was decreased.

结果表明，通过选用强度优异的轴套作为摩擦副，缩减沟槽尺寸以增加轴套与轴颈的接触面长度，改善了摩擦副的润滑状况，减少了磨损，满足了生产需要。

The closest cylinder hole in the block has a sleeve in place, while the other sleeve is displayed outside the block.

最接近的缸孔块有一个套筒到位，而其他外套筒显示块。

Which has been standardized sleeve roller chain This chain is the chain plate from the inside and outside the chain plate, sleeve, pin, roller composition.

其中套筒滚子链已标准化，这种链是由内链板、外链板、套筒、销轴、滚子组成。

The CDI's Sleeve Option allows an easy and ergonomic change-over from plate to sleeve.

课程发展处的袖子选项允许一种简单，符合人体工程学的变化：从盘交给套。

In order to decrease the loss energy, a new kind of sleeve valve of hydraulic impactor is designed. It takes the technical measure of cone valve and optimum unequal polite of valve. The sleeve valve has features of little leakage, little pressure loss and low energy cost.

为了降低能源消耗，研制了一种新型的液压冲击器配油阀，该阀采用锥阀阀口形式和优化的不等阀开口量技术，使配油阀泄漏量小，阀口压力损失小，换向运动能耗低，液压冲击器效率高。

Characterstic function of ultrasonic sleeve sewing machine Apply to the cylinder-shaped welding of non-woven fabrics,such as sleeve sewing,trouser and other cylinder-shaper sewing.

超声波袖筒机特色功能用于无纺材料的筒状焊接，如袖筒缝合、裤管缝合，及其它筒状缝合。

The results showed that the wear-resistant belt in drill joint was actually an isolation belt, which could protect the drill joint and sleeve from serious abrasion, and the optimization and improvement of its performance was the technical key to preventing sleeve from serious abrasion.

结果表明，钻杆接头耐磨带实质上是一个隔离带，用以保护钻杆接头和套管免遭强烈磨损，接头耐磨带性能的优化与改善是防止套管强烈磨损的关键技术措施。

It gives us full access to research and development around sleeve concepts for direct laser engraving and further expansion of our LAM sleeve concepts.

这使我们周围的直接激光雕刻，我们的林套概念套概念进一步扩大充分利用研究和开发。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。