查询词典 sleeve dog

The results showed that the wear-resistant belt in drill joint was actually an isolation belt, which could protect the drill joint and sleeve from serious abrasion, and the optimization and improvement of its performance was the technical key to preventing sleeve from serious abrasion.

结果表明，钻杆接头耐磨带实质上是一个隔离带，用以保护钻杆接头和套管免遭强烈磨损，接头耐磨带性能的优化与改善是防止套管强烈磨损的关键技术措施。

It gives us full access to research and development around sleeve concepts for direct laser engraving and further expansion of our LAM sleeve concepts.

这使我们周围的直接激光雕刻，我们的林套概念套概念进一步扩大充分利用研究和开发。

Based on finite element dynamic model of expansion casing with rubber sleeve, casing deformation and stress change inside casing, contact pressure at both sides of rubber sleeve and expansion parameter changes caused by friction factors during the expansion are analyzed.

根据带有橡胶筒的膨胀套管有限元力学模型，对套管膨胀过程中橡胶变形和套管内的应力变化、橡胶筒两侧的接触压力，以及摩擦因数引起的膨胀参数变化等做了分析研究；对橡胶筒的厚度、长度做了定量和定性分析，发现在橡胶与套管之间的接触摩擦因数作用下，橡胶过长将会在纵向产生&堆积&现象，在有限空间中，使其受较大的接触压力而失效。

Plunger core of this pump is made of metal tube with several radial holes in the middle. There is an elastic expansion sleeve on the middle screen plunger core; several wear resistance seal rings are on the expansion sleeve.

该泵的柱塞芯由中部开有若干个径向槽孔的金属管制成，柱塞上装有一个弹性伸缩套，套在中心筛管柱塞芯上，在弹性伸缩套外面套有若干个耐磨的密封环。

As well, it would seem that preheating the sleeve to about 150°C would help by avoiding rapid freeze-up of the propellant as it comes into contact with the sleeve (clearly, this may pose a problem with the adhesive with sleeves that are glued, as the adhesion may fail).

以及，似乎预热套筒约150 ° C时，将有助于避免快速冻结行动的推进剂，因为它接触到与套筒（很明显，这可能会构成问题，与胶粘剂的袖子是胶合板作为粘附可能会失败）。

Married women wear "left sleeve" kimono, unmarried young lady wearing "vibration sleeve kimono."

已婚妇女多穿&留袖&和服，未婚小姐多穿&振袖&和服。

Aimed at all kinds of damage phenomena in the sleeve usage of oil-film bearing in the backup roll of Baoshan 1580 hot strip mill,during the process of elastic conjunction between sleeve and rollneck,deformation and load properties are quantitatively analyzed by boundary element method for 3D elastic and plastic contact problems.

针对宝钢1580热连轧机精轧机组支承辊油膜轴承锥套使用中存在的各类损伤问题，利用三维弹塑性接触问题边界元法定量分析了轧机油膜轴承锥套与轧辊辊颈过盈装配过程中的变形和载荷特性，得出了装拆过程中不同的胀型压力和轴向推力条件下锥套接触压力延母线方向的变化规律，同时锥套端部和密封槽附近接触压力峰值的存在是加速锥套损伤及降低其使用寿命的重要原因。

Remove gauging at sleeve head, ensure that sleeve does not puff out above cuff edge.

原办见图。请问上次两点批办意见是什么意思啊？？？急急。。。在线等。。。。。

First of all, horizontal swing to solve big problems, re-allocation of a motor sleeve (with the bronze with stent hole so), so that the electrical sleeve just in bronze wall bracket can rotate, reducing the gap; further axial movement to solve the problem with the motor shaft with Hexagon Hexagon washer so thick 0.6mm.

首先解决横向摆动大的问题，重新配做一个电机轴套，使电机轴套在铸铜支架内壁刚好能转动，减小间隙；再解决轴向窜动问题，与内六角电机轴配做内六角垫圈，厚0.6mm。

Figure 2-30 is a three commonly used control valve sleeve sleeve diagram, due to changes in hole size is different spool move When the flow area is also different, in order to achieve the required flow characteristics.

图2—30是三种常用套筒控制阀的套筒示意图，由于开孔面积变化不同，阀芯移动时，流通面积也不同，从而实现所需流量特性。

Dixie itself is a nickname for the American South.

Dixie 本身是美国南部的别称。

I think John Terry epitomises that and a big reaction is what we will be looking for.

而我认为特里就是这样一个典型，他正是我们期望看到的那个领秀。