查询词典 sizing

Aluminium sulfate has been used as the rosin sizing precipitant for along time, but it is only valid in acid pH.

硫酸铝用作松香施胶的沉淀剂已经有很长的历史了，但它只适用于酸性条件。

Contact-impact model and its discrete schemes for revolute pairs with small clearances ;2. Based on the theory of contact dynamics,the dynamic model with clearances of sizing press roll was established using the method of numerical simulation.

基于接触动力学的理论，利用数值模拟的手段建立了调宽机含间隙的动力学数学模型，采用定步长四阶Runge-Kutta数值积分的方法，详细研究了运动副内间隙对接触力的影响规律。

Based on the theory of contact dynamics, the dynamic model with clearances of sizing press roll was established using the method of numerical simulation. The paper studied the effect of clearances on contact force inner Mechanism joints detailedly by the method of numerical integration of fix step length four orders Runge-Kutta.

基于接触动力学的理论，利用数值模拟的手段建立了调宽机含间隙的动力学数学模型，采用定步长四阶Runge-Kutta数值积分的方法，详细研究了运动副内间隙对接触力的影响规律。

The results show that, with the expansion cone angle remaining unchanged, the sizing length of expansion cone does not have much effect on the residual stress of casing after expansion, but it has much effect on the expansion force required by tube expansion. The expansion cone angle has no effect on the maximum residual stress of casing, but it has remarkable effect on expansion force. When the radial component force of expansion force is greater than the material's tensile strength, the damage to the material will arise.

研究结果表明，在膨胀锥锥角保持不变的情况下，膨胀锥定径长对膨胀后套管的残余应力没有太大影响，但对套管膨胀所需要的膨胀力有较大影响；膨胀锥锥角对套管最大残余应力没有影响，但对膨胀力的影响十分明显，当膨胀力的径向分力大于材料的抗拉强度时，材料将发生破坏。

The processing practices and the production and technical keys in warp ing sizing, reeding, healding and weaving, etc.

介绍了在生产两种经纱提花条织物时，整经、浆纱、穿筘、穿综、织造等工序的工艺实践和生产技术要点。

In the article are introduced the production process and the weaves and colors design of a single pattern multi-weave broad fabric woven by dyed yam with key technical measures of warping, pattern arrangement, sizing and healding and reeding processes also discussed.

摘要介绍了色织宽幅多组织独花面料的色织工艺流程及组织、色彩设计，叙述了整经排花、浆纱及穿综穿筘工序的技术措施。

The main production and operation of ultra-thin double-sided tape, strong double-sided tape, high temperature double-sided adhesive tape, conductive double-sided tape, double-sided thermal tape, Teflon tape high temperature, high temperature Masking tape, high temperature polyimide tape, thermal insulation tape , copper foil, aluminum foil conductive adhesive tape, anti-static tape, security tape, waterproof tape, anti-theft tape, non-slip, shock-proof tape, shading tape, reflective tape, protective film, fiber tape, spray adhesive tape, kraft tape, tape Mara, electrical tape, acetate cloth tape, fingerprints, tape, wall tape, seal tape, sealing tape, stickers, all kinds of insulation, high temperature resistant, UL certification shaped materials, sizing, cutting processing.

主要生产经营超薄双面胶带、强力双面胶带、高温双面胶带、导电双面胶带、导热双面胶带、铁氟龙高温胶带、高温美纹胶带、聚酰亚胺高温胶带、导热绝缘胶带，铜箔、铝箔导电胶带、防静电胶带、防伪胶带、防水胶带、防盗胶带、防滑、防震胶带，遮光胶带、反光胶带，保护膜、纤维胶带、喷涂胶带、牛皮胶带、玛拉胶带、电工胶带、醋酸布胶带、指纹胶带、挡墙胶带、封缄胶带、封箱胶带、不干胶、各种绝缘、耐高温、UL认证异形材料、上胶、模切加工。

The calculation accuracy of the solid content is not high because the errors occurred during the mensuration of sizing's refractivity ,therefore it is necessary to test the dependability of these data.

根据折射率来计算混合浆的含固率时，由于测定折射率时存在误差，导致了含固率的计算精度不高，故有必要对所测折射率进行置信度的验证。

By correctly sizing the cavity and aperture, the device can be made series resonant at any desired frequency.

通过适当选择空腔和入口孔的尺寸，可保证在要求的频率下获得共振状态。

Of high-speed wire rod mill of using reducing sizing mill were introduced.

介绍了使用减定径机的安钢高速线材轧机的工艺特点及在生产管理、轧机调整、产品精度控制等方面的经验。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。