查询词典 sintering
- 与 sintering 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Zinc titanates ceramics have low sintering temperature (1100℃) and promising properties, and they can be sintered at 1100℃ without sintering aids.
钛酸锌陶瓷具有优良的微波介电性能,而且不加入烧结助剂即可于1100℃烧结。
-
The results showed that the adsorption capacity of the adsorbent reaches greatest with 30%carrying acid in adsorent,stoving temperature 105℃,sintering temperature 240℃ and sintering time 4h.
实验结果表明,当吸附剂的载酸量为30%,烘干温度为105℃,焙烧温度为240℃,焙烧时间4h条件下,吸附剂的吸附能力最大。
-
Because of the unstablity of sinters,the variability of sintering process and the increasing of sinter output etc,the hot pipe thermoconverter will occur some problems during its application in sintering plant The corresponding improvements and perfecting were presented in this paper
由于烧结矿料的不稳定性、烧结工艺的变化以及烧结矿产量的变化等原因,热管蒸汽发生器在烧结中应用时,遇到了一些问题,严重时还影响到用户的正常生产,因此本文介绍了对热管蒸汽发生器系统进行的相应改进和完善。
-
The selection of the sintering parameters has effect on the mechanical properties of the sintering materials to some extent.
烧结参数的选择对烧结材料的力学性能有一定的影响。
-
Finally, sintering temperature and sintering atmosphere have been studied.
最后研究了材料的烧结温度和烧结气氛。
-
The results show that the performance of sintering part changes along with hydrogen content in the sintering atmosphere.
结果表明:烧结件的性能随烧结气氛中氢的含量的变化而变化。
-
For example, the water content of sintering mixture is one of the important factor in sintering production.
例如,烧结混合料水分就是烧结生产工艺中一个非常重要的参数。
-
In comparison with the sample directly sintered at 650 ℃<TN, an interesting, irreversible transformation in the crystal structure of the MgB2 phase is observed with the sample going through the stages of initial sintering at 750 ℃, then re-sintering at 650 ℃ in an Mg-rich environment after the processes of regrinding and pressing.
把直接在650 ℃<T N,烧结的样品与先在750 ℃下烧结,之后又再次重磨和处理后,并于富镁的环境中在650 ℃下再烧结处理的样品相比较,观察到了MgB2的不可逆的晶体结构转变。
-
The results shows that the flow characteristics of SiC-AlN granulated powder is obviously promoted after spray drying and a suitable particles grade match. With the increasing of pressure, the density of green body increases by the style of ladder at the pressure range of 4080 MPa, 80160 MPa and 160220 MPa, the green body is uniform and densification without hard pelleted particles above 160 MPa. The pressureless sintering SiC-AlN multiphase ceramic possesses superior sintering properties and mechanical properties. It is due to the rampart formation of AlN to SiC grain growth and the reaction of SiC and AlN to form 2H solid solution. It results in the grain fining, crack expansion producing bypass and deflection, fracture section producing tearing-open and pulling-out effects, which cooperatively improves the strength and fracture toughness of the multiphase ceramics.
结果表明:喷雾造粒后,复合粉体的流动特性显著提高,粒度级配合理;随着压强增加,坯体密度在40~80、80~160和160~220 MPa范围内呈现阶梯式增长,160 MPa以上成形后素坯均匀致密,无硬球颗粒存在;无压烧结SiC-AlN复相陶瓷具有优越的烧结性能和力学性能,这是由于AlN对SiC晶粒形成生长势垒,并反应生成2H型固溶体,从而细化晶粒,导致裂纹扩展产生了绕道与偏转效应,呈现晶粒撕裂与拨出现象,协同改善了复相陶瓷的强度及断裂韧性。
-
Results show that chemical reaction between additives Al2O3 and Y2O3 accelerated the liquid phase sintering and the formation of the YAG non-crystalline,which was beneficial to improving fracture toughness of Cf/SiC composites.Higher sintering temperature resulted in the strongly bonded fiber/matrix interface.Fiber push-off,crack deflection and grains bridging are main toughening mechanisms of silicon carbide cera...
结果表明:烧结过程中,烧结助剂Al2O3、Y2O3之间发生化学反应,促进液相烧结,形成晶界间的次晶相YAG(3 Y2O3.5Al2O3),有利于提高复合材料的断裂韧性;在较高烧结温度下,碳纤维、烧结助剂与基体间发生反应,形成较强结合界面;纤维拔出、裂纹偏转和晶粒桥联是碳化硅陶瓷的主要增韧机制。
- 推荐网络例句
-
As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.
每逢看到沃林顿那刚毅的脸,那乌黑、忧郁的眼睛,她便会相信,他一定作过不幸的爱情的受害者。
-
Maybe they'll disappear into a pothole.
也许他们将在壶穴里消失
-
But because of its youthful corporate culture—most people are hustled out of the door in their mid-40s—it had no one to send.
但是因为该公司年轻的企业文化——大多数员工在40来岁的时候都被请出公司——一时间没有好的人选。