查询词典 sintered

The effect of post-sintering heat treatment on the mechanical properties of a liquid phase sintered tungsten-base ahoy (95W-3.SNi-1.5Fe) has been investigated.

研究了液相烧结钨基高比重合金(95W-3.5Nj-1.5Fe)烧结后热处理对力学性能的影响。

It is specialized in studying, manufacturing, marketing and after-sell service of magnetic material, and mainly produces sintered permanent Alnico magnets, bonded permanent magnets, Alnico magnet powder and assembled magnetic materials, which is widely applied into different kinds of meters, sensors, motors and telecommunications.

它是专门从事研究，制造，营销和后销售服务的磁性材料，主要生产烧结磁体永久磁钢，粘结永磁，铝镍钴永磁粉和组装磁性材料，这是广泛应用于不同种类的米，传感器，汽车和电信。

The precursor powder materials were sintered by pressureless treatment at 600℃ and 900℃, respectively. XRD results show that the powder is in the form of a single cubic fluorite structure when sintered at 600℃.

在600℃和900℃下分别对初始粉体进行无压煅烧，XRD表明，在600℃时形成了单一的立方萤石结构。

By actualize dead lime slaking technology,the blended mix and sintered ore size were improred,the sinter process was aggrandized,the question of white in sintered ore was solred,the production of simtered ore was adranced and quality was improved.

通过实施生石灰消化技术，改善了混合料及烧结矿粒度组成，强化了烧结过程，消除了烧结矿中&白点&问题，提高了烧结矿的产量，改善了烧结矿的质量。

Using modified conventional powder metallurgy process for sintered Nd-Fe-B magnets , including annealing of ingot alloy, hydrogen decrepitating, modified jet mill and adding additive during jet milling, we have mass-produced high performance and high corrosion resistance sintered Nd-Fe-B magnets from a conventional ingot alloy without strict protections against oxidation.

利用改进的传统粉末冶金工艺(铸锭热处理、氢爆、改进型气流磨设备以及在气流磨中掺入添加剂等)，在无严格的防氧保护情况下，从传统合金铸锭出发，工业化生产出具有高耐蚀性的N48～50档烧结Nd-Fe-B 磁体。

Comparing the magnetic properties of sintered magnets from HD powders and the degassed powders, it is found that the sintered magnet from HD powders gets excellent properties at a temperature of 20～30℃ lower than the magnet from the degassed powders.

例如，HD磁粉在10T的外磁场下所受到的转动力矩甚至还没有350℃脱氢磁粉在2T磁场下受到的力矩大，当磁粉的c轴与磁场方向成π/5（36°）角度时，两者受到的转动力矩分别为1.123×10〓Nm和1.202×10〓Nm。

The formed body is degreased at a temperature having the formed body not sintered. A sintered body is provided by sintering the degreased body.

在不烧结成形体的温度使成形体脱脂，然后烧结已脱脂的成形体而得到烧结体。

To get a property comparison of GXHJ－ 1 sintered welding agent with SJ101 sintered welding agent, related tests were carried out, including deposited metal test, lab butt－ joint plate test, single－ welding stick operation test, double－ welding stick operation test as well as operation test with H08C welding stick, focusing differences of the two in terms of technological properties and weld seam impact toughness.

为了比较 GXHJ－ 1和 SJ101两种烧结焊剂的性能，分别从熔敷金属性能试验、实验室对接板试验、单丝焊生产、双丝焊生产等方面及在匹配 H08C焊丝的条件下进行了工艺性能和焊缝冲击韧性对比。

The grains of sintered body were enlarged and the phenomena of particle pulling-out decreased with increasing alumina content. ZrO〓/Al〓O〓 sintered composite body could reduce the alumina grain size dramatically.

当ZrO〓含量较多时，烧结体颗粒较小，晶粒拔出现象明显，随着Al〓O〓含量的增加，晶粒长大，颗粒主要是穿晶断裂。

Apart from the working limitations resulting from its structural property, the flat plate heat pipe carries out heat dissipation through the evaporation and condensation of the working fluid. Thus, if the working angle of the fluid is adverse to its backflow, the heat pipe will fail easily. Furthermore, not the orientations of all the heat sources are favorable to the functioning of the heat pipe. To compensate for this drawback, this research focuses primarily on the development of a composite structure which will reduce the effect of gravity on the working fluid. Generally speaking, the heat pipe is divided into three main categories: the groove type, sintered metal type and mesh screen type, as shown in Table 2. As far as capillary force is concerned, the sintered metal type and mesh screen type show better performance. As mentioned in R.

平板式热管除了因其结构特性而产生的工作极限之外，由于其作用乃是透过工作流体的蒸发及凝结进行散热，故若是其工作角度不利于液体之回流，便容易使热管失效，且并非所有之发热源都是位于有利于热管工作之位置，因此本研究之主要目的为设计一可减少重力对工作流体影响之复合式结构；一般而言，热管之结构大致可分为沟槽、烧结及网格三种(如表2所示)，其中烧结及网格结构有较佳之毛细力，在 R。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐