查询词典 simulation

The main idea of this work is to find a thermal solution for Qosmio-F50 laptop computer of Toshiba company by performing numerical simulation first, and then, by verifying the result of simulation by molding tool equipped with heater. The developed design has been implemented into the product to prove the performance.

中文摘要本论文的研究主题，在针对东芝公司以上市之笔记型电脑Qosmio-F50，利用数值模拟软体为散热系统配置作先行规划分析，再以实际含发热源之模具，实际测试验证数值模拟结果的正确性，最后将设计导入实机。

The simulation of drawing process is realized. The measurement of edge contraction and distribution of the thickness in a tryout piece is carried out and compared with the simulation results.

完成了该覆盖件的拉延工艺成形模拟，测量了试模时该覆盖件的拉延工序件的边缘进料量和厚度，并与模拟结果进行了比较。

Electro-acoustic equipment categories: electro-acoustic device test system, characteristics of piezoelectric transducer tester, test sensitivity sorting device, sound level meter, precision signal source Sweep, Sweep audio device, the standard sound source, standard test microphone, IEC318 Simulation of the ears, mouth simulation, speakers polarity tester, telephone analyzers, such as electro-acoustic type of testing equipment.

电声器件测试系统、压电换能器特性测试仪、灵敏度测试分选仪、声级计、精密扫频信号源、音频扫频仪、标准声源、标准测试话筒、IEC318仿真耳、仿真嘴、喇叭极性测试仪、电话分析仪等电声类测试仪。

The lift course of hanging device on wheat no-tillage planter was simulated by using the software of ADAMS. Some important parameters were obtained such as height of the working part relative to ground, the distance between the working part and the rear wheel of tractor, the angle of road pass and the force of hanging point, etc. The key parameters of the hanging device and its best working parameter of hanging device were found out through optimization simulation. Simulation results showed that suspension point had minimum force when variable DV_1 and DV_2 gained corresponding maximum and minimum at scope of structure limit.

应用ADAMS软件对小麦免耕播种机悬挂机构提升过程进行了动态仿真，得到了工作部件的位置高度、工作部件与拖拉机后轮之间的间距、路面通过角以及悬挂点的受力等参数，找到了悬挂机构的关键参数，通过优化仿真，得到了悬挂机构的最佳工作参数，仿真结果表明，设计变量DV_2、DV_3在结构受限范围内分别取其最大值和最小值，悬挂机构悬挂点受力最小。

By using simulation-analysis software CFD,STAR-CD,a three-dimensional simulation analysis was conducted of the semi-volute suction chamber of a gas-oil multiphase pump for flow fields at different void fractions.

利用CFD模拟分析软件———STAR-CD，对油气混输泵半螺旋形吸入室在不同含气率下的流场进行了三维模拟分析。

Simulation on steam system of the secondary loop of nuclear power plant is an important part of research of real-time, whole range, whole functional simulation of nuclear power plant.

核动力装置二回路蒸汽系统仿真是核动力装置实时、全范围、全功能仿真机研制工作的重要组成部分。

A simulation research is conducted on the example of six-phase double star winding shifted by 30°synchronous motor.In order to investigate the control algorithm of multilevel inverter , high harmonics as well as its problems, a mathematical model of the control algorithm based on the voltage space vector is built. For the first time, the principle along boundary is introduced to confirm the chosen switch state when many switch states are corresponding to the same vector. Simulation analysis and hardware realization are conducted with the combination of diode clamped three-level inverter and five-level inverter.

建立了基于空间电压矢量控制算法的仿真模型；仿真研究中采用对偶小矢量搭配改善中点电位波动的问题；针对多个开关状态对应同一待选矢量的问题引入&循边原则&确定被选择的开关状态；对过调制问题进行了相应的处理：结合二极管嵌位式三电平逆变器和五电平逆变器进行了仿真分析和硬件实现。

The simulation points out a way for designing and manufacturing nanomaterials with totally different microstructures.2.The linear homopolymers have been added into a ABC 3-miktoarm star terpolymers system by dynamic density functional theory simulation. The areas of B phase domain and the interval between two nearest neighbour B phase domains shift with the accession of the linear polymer.3.A Petri net model was built to simulate the heat shock response in E.coli.

我们构建了大肠杆菌热休克反应的Petri网络模型，并应用化学反应动力学随机算法进行了模拟计算，观察其动力学过程，通过观测体系中平衡态下分子数目与反应速率常数间关系，总结了反应对体系平衡的影响规律，并由观测到的现象，对调控因子α的自身表达的调控机制作出推测：调控因子α的调控机制有可能是受网络控制的。4。

In order to solve the shape problem of profiling processing space complex surface, general mathematical model of a wooden staircase handrail elbow end section curve has been set up, the VC and Pro/E for the staircase handrail elbow joint simulation have been used to do simulation.

为了解决依据靠模加工空间复杂曲面成型困难的问题，建立木制楼梯扶手弯头端截面曲线的通用数学模型，利用VC和Pro/E对楼梯扶手弯头进行仿真验证。

Warm-hot control forging process of automobile spline shaft is investigated by using physical simulation and numerical simulation.

采用物理模拟和数值模拟相结合的手段，对汽车花键轴的温热控制精锻工艺进行了深入的研究。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失