查询词典 shear strength

By field-testing methods, such as static cone penetration test, field vane shear test, and pore water piezometer test, the variation of strength and the pore water pressure are measured at real time, and the marine hydrodynamics' impaction on the consolidation process of the sediments in the Yellow River Estuary was studied. It is shown that the self-consolidated sediments have a very fast consolidation rate, under self-consolidation, in 72h, the consolidation degree reaches 37% and about 142h the pore water pressure disperse over, while under the hydrodynamics, in 72h the consolidation degree reaches 52% and about 195h the pore water pressure disperse over.

在黄河三角洲刁口叶瓣潮坪上，开挖2m×1m×1m的试坑，现场取土配置黄河口快速沉积形成的流体状堆积物，以铁板部分覆盖试坑隔绝波浪和潮流作用，利用微型贯入、静力触探、十字板剪切试验、孔隙水压力监测等原位测试手段，实时测定快速沉积的海床土强度发展以及孔隙水压力消散情况，研究快速沉积的粉质海床土分别在自重条件下以及在波浪和潮波等水动力作用下的固结过程。

The control of the strength of shear field, plasticization and production output can go on separately.

实现剪切场强度调节与熔体塑化和产量控制相分离。

Situated in the warm ocean, it is expected that LINGLING can maintain strength before encountering substantially lower sea surface temperatures and increased vertical wind shear after recurvature.

预料玲玲可在温暖的海水中维持强度。 t+24 之后，随著玲玲的纬度增加，它将会受较冷的海水及较强的垂直风切变影响而减弱。

When the specimens were failed in the surface shear off deformations, resin type rather than the fiber type appeared to dominate the bond strength of FRP bars.

而是FRP筋表面螺纹凸起部分与核心处FRP筋发生剪切滑移，表面粘砂层研磨成粉状，成纵向剪切破坏。

In view of the questions in theoretic analysis and numerical simulation with the finite element method,the separation criterion of chips, the surface contact, the setting of friction coefficient,and the thermal stress coupling are researched. A simulation example is presented by applying the finite element analysis software-ANSYS,and the change of stress and strain in metal cutting process, the forming of shear plane and the influence of the temperature field on metal cutting are analyzed. The tool's strength is also analyzed.

基于理论分析和实际有限元数值模拟计算中遇到的问题，研究、讨论了切屑分离标准、表面接触、摩擦系数的设定、切屑与工件之间的连接以及热应力耦合分析等各项技术，并应用大型有限元分析软件ANSYS，具体分析了金属切削过程中应力和应变的变化、剪切面的形成以及温度场对金属切削的影响，并依此对刀具作强度分析，得到若干结论。

It is assumed that the shear stress is proportional to the strength of the workpiece material.

它假设剪切应力正比于工件材料的强度。

These flakes, in turn, reduce the strength of the secondary shear zone, decreasing tool-chip interface and wear.

这些片状，依次减小第二剪切区中的力量，降低刀具和切屑接口处的摩擦和磨损。

The method for calculating the axial force, bending moment and bending deflection sucker rod string with centralizer is obtained applying compressionalto - shear buckling continuous beam - string theory- The design method for sucker rod string with weighting rod is presented in this paper, which takes the modified Goodman stress diagram as strength design principle and...

应用纵横弯曲连续梁柱理论得到了求解带扶正器的抽油杆柱的轴力、弯矩和挠度计算公式；以修正的Goodman应力图为强度准则，并考虑杆柱刚度条件，提出了水平井中抽油杆柱加重设计的方法。最后给出了某油田1口井的抽油杆柱设计实例，说明了该万法的正确性。

Although cancellous screw xation improves torsional strength, implant failures typically occur with bending and vertical shear loads.

尽管松质骨螺钉具有较好的抗旋转强度，但失败通常发生于屈曲及剪力负荷如负重。

After thermal cycling testing, when the strength of equiaxial grain regions or thermally grown oxidation layer became lower than the shear stress, the spallation occurred along the vertical crack network.

经过长时间热循环后，当陶瓷层等轴晶区的强度或者热氧化生长层的强度小于边缘效应产生的剪应力时，涂层在试样的中部以垂直裂纹网格形状发生剥落失效。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失