查询词典 shear strain

The results show that, consolidated deviator stress ratio has the most significant effect on normalized pore water pressure developed with number of cycles. And the normalized pore water pressure developed with generalized shear strain is independent of various initial stress condition.

研究表明：非均等固结条件下，固结偏应力比对归一化后的孔隙水压力随振次增长模式影响最为显著；不同固结条件下的归一化孔隙水压力随应变增长模式却基本相同。

It is found that the main source of fillet weld's angle distortion is the inherent shear strain component ε but not the transverse inherent normal component.

结果发现：角焊缝产生角变形的主要根源是固有剪切应变，而不是传统思维认为的横向固有正应变，且角变形的大小与固有剪切应变的分布形式密切相关。

Based on the current development of VED in structural control and its fractional derivative model, the finite element formula of VED is erected by using three different assumptions of the shear strain.

针对粘弹性材料的分数导数模型，采用不同的剪应变的假设，推导了粘弹性阻尼器的有限元计算公式，通过粘弹性阻尼器在一单自由度系统的控制上的应用，确定了其计算模型。

Moreover, this paper analyses the shear strain and compressive stress and loading frequency dependence of the damping ratio.

另外，对叠层橡胶支座的阻尼比随剪应变、压应力及荷载频率的变化情况进行了分析。

The recovery of the pseudocubic angle of LSMO resulting from the relaxation of the shear strain introduced by the growth of rhombohedral LSMO on cubic LSAT was suggested to be the origin of the superlattice structure.

不对称的(103)倒易空间图强有力地证明了这面内调制结构源于因菱形的LSMO和立方衬底LSAT之间的角度失配引起的一种剪切应力的弛豫而导致LSMO薄膜中赝立方角的恢复。

The effect of rake angle and cutting velocity on the shear strain imposed in the chips, microstructure and hardness of chips are highlighted in a variety of metals and alloys.

本文对比了不同的金属和合金在各种刀具前角和切削速度条件下，切屑上产生的剪应变、切屑的微结构及其硬度的变化规律。

The results show that the main cause of the angular distortion of the lap joint is the non-uniform distributed inherent shear strain component that is vertical to the weld line and exists in the plane paralleling to the weld line.

结果表明：搭接接头焊接角变形的产生主要是由焊缝及其附近区域与焊缝平行的平面内垂直于焊缝方向上不均匀分布的固有剪切应变分量引起的。

In this case, the average shear strain including the non-liquefied surface layer is 1.5%.

在这种情况下，平均剪应变包括非液化表面层是1.5 ％。

Results show that when improving spot pitch in weld bonded joints with high elastic modulus adhesives, stresses in weld spot zone are decreased while stresses and strains at edges of overlap region are increased slightly. For the joints with low elastic modulus adhesives, both stress concentration degree at the weld spot and the shear strain at edges of overlap region are increased with the spot pitch increasing.

结果表明，高弹性模量胶粘剂胶焊接头中，增大焊点间距，焊点区应力减小而搭接区边缘胶层中的应力应变略有增大；低弹性模量胶粘剂胶焊接头中，焊点处应力集中程度和搭接区边缘胶层中的剪应变值都随焊点间距的增加而增大，增加焊点间距，两种接头的胶层断裂强度都将降低。

Defined the linear strain rate, the shear strain rate, and the rigid rotation rate.

定义线性应变速率，剪切应变速率，刚体旋转速度。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。