查询词典 shear plane

The instructive conclusion was: 1 under the vertical loading, the shear-lag effect was produced badly, more severer under concentrated loading than under uniform loading .2 the longitudinal bending deformation of the beam flange was true of the imitating plane assumption of deformation . 3 the width length ratio was confirmed as the first factor working on the shear-lag effect among all the geometric parameters;4 the shear-lag coefficient of simple-supported box-girder was severer than the continuous box-girder, the shear-lag effect in the inner supported section of continuous beam was much more severer, we need paying more attention for it in designing. 5 the non-liner characteristics of material deformation have littlie influence on shear-lag effect in BGCW. 6 the experiential calculating formulation and calculating diagram for the effective flange width was raised with the only factor of the width-span ratio., but the primary location of axis of bending moments should not be changed while calculating the inertial moment .

研究认为：1室内模型试验和空间有限元分析结果均表明波形钢腹板组合箱梁在竖向荷载作用下，翼板出现了典型的纵向应力剪滞效应。2在竖向荷载作用下，截面高度上各点纵向正应变分布认为可符合"拟平截面假定"，以此作为波形钢腹板组合箱梁抗弯计算的基本假定。3箱梁宽跨比是影响波形钢腹板组合箱梁翼板剪滞效应的主要因素。4连续波形钢腹板组合箱梁的翼板剪滞系数大于简支梁，且连续箱梁内支点截面翼板剪滞效应相当严重，对此需十分重视。5当混凝土翼板受力由弹性阶段进入弹塑性阶段时，材料的非线性特性对翼板的剪滞效应影响甚微。6提出了根据组合箱梁的宽跨比参数来计算翼板有效宽度比的经验公式和计算图表，但箱梁截面抗弯惯性矩的计算不应改变原先的截面中和轴位置。

Similarly the stress gradient across the shear plane has to be very large to be practical.

同样在实际运用中越过剪切面的应力梯度必须很大才行。

The results showed that most multiaxial fatigue cracks were initiated and propagated along the direction of maximum shear plane.

利用扫描电镜对疲劳试样的外表面和疲劳断口进行观察，研究了多轴疲劳裂纹萌生和扩展规律，发现裂纹基本上沿着最大剪切平面萌生和扩展。

Variation of striper force and clearance between punch and die plate with respect to shear plane and die stress were analyzed .

分析了不同压边力和凸凹模间隙对精冲断面质量和模具应力的影响关系。

The characteristics of strains on the maximum shear plane were analyzed under tension-torsion multiaxial fatigue loading.

针对拉扭多轴疲劳加载情况，分析最大剪切平面上的应变特性。

In view of the questions in theoretic analysis and numerical simulation with the finite element method,the separation criterion of chips, the surface contact, the setting of friction coefficient,and the thermal stress coupling are researched. A simulation example is presented by applying the finite element analysis software-ANSYS,and the change of stress and strain in metal cutting process, the forming of shear plane and the influence of the temperature field on metal cutting are analyzed. The tool's strength is also analyzed.

基于理论分析和实际有限元数值模拟计算中遇到的问题，研究、讨论了切屑分离标准、表面接触、摩擦系数的设定、切屑与工件之间的连接以及热应力耦合分析等各项技术，并应用大型有限元分析软件ANSYS，具体分析了金属切削过程中应力和应变的变化、剪切面的形成以及温度场对金属切削的影响，并依此对刀具作强度分析，得到若干结论。

Our main products are various specifications for small and medium-sized two-roll, four roll-precision rolling mill, spiral round air duct air duct molding machines and other equipment, as well as slitting machine, shearing machine, hydraulic shear plane angle, such as sheet metal machinery.

公司主要产品有各种规格的中小型二辊、四辊精密轧机，螺旋圆风管机等风管成型设备，以及纵剪机、剪板机，液压剪角机等板金机械。

After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.

3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。

Introduce the cohesion-friction model of rock strength theory, and extend the model to select the strength of sliding plane, discuss the variation rules of peak strength and residual strength under different normal stress, and then present the selection model of shearing strength. After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.

3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。

The shear plane microstructures of Cu-9Ni-2.3Sn(C72500) alloy after shearing deformation and then annealed at 550 ℃ for 2 h were observed by OM and SEM.

摘 要：采用金相显微镜和扫描电镜研究Cu-9Ni-2.3Sn(C72500)合金经剪切变形后合金切面的微观组织以及随后在550 ℃退火2 h后切面的组织变化。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。