查询词典 shear plane

Influence of shear plane inclination and location as well as buffer properties on the damage caused to the canister

剪切面的倾斜度和位置以及缓冲物的性质对废物罐损伤的影响

The angle made by the shear plane with the cutting speed vector,Φ is a very important parameter in metal cutting.

由剪切面和切削速度矢量形成的角度Φ在金属切削中是一个十分重要的参数。

The negative shear area and angle φ′of negative shear plane in metal cutting are first found out and verified by experiments, and effects of angle φ′of negative shear plane on the change of cutting direction fracture formation is experimental studied in orthogonal cutting.

首次提出并证实了金属切削中负剪切区域和负剪切角φ′的存在，讨论了负剪切角φ′对切削方向亏缺形成及其变化的影响。

And the formula for angle of shear plane is modified by chip shortening coefficient.

在HSM-700高速铣床上进行了主要考虑转速影响的单因素铣削力、铣削温度测试实验。

There were same trend of temperature distribution in rake plane and shear plane, and the feasibility of numeric simulation through was validated through comparing the result of experiment with simulation result.

通过对数值模拟结果和试验结果的比较，在前刀面和剪切面上温度分布具有相同的趋势，验证了数值模拟的可行性。

The shear angle in the shear plane will crease with the cutting velocity.

切屑剪切平面之剪切角会随著切削速度的增加而增加。

It is found that there is a particle migration towards lower shear-rate regions on the shear plane, which does not exist on the vorticity plane.

发现球体对在剪切面有向低剪切率方向漂移的运动，而在涡旋面这种漂移运动并不存在。

The results show that the frictions caused by the wall of shear box will influence the distributions of stresses in specimens and the normal pressure stresses on the shear plane.

结果表明，剪力盒壁摩擦力将会影响试验土样中的应力分布和剪切面上的正压应力值。

Fractography analysis shows that the global tension failures trimly,because of matrix cracks and tension fracture of fiber and the compression specimens failure in a shear plane about a little angle to the compression loading direction because of delamination and longitudinal fiber shear fracture.

其拉伸断口较为平齐，基体开裂以及纤维拉伸断裂是主要破坏形式；压缩破坏呈现剪切断面，压缩断面和压缩加载方向形成一个较小夹角，层间分层和纵向纤维剪切断裂是其主要破坏形式。

The results show that some twin crystals and honeycomb structures appear in the shear plane and many kinds of deformation mechanism exist such as extruding, kinking and so on. When annealed at 550 ℃ for 2 h, the recrystal gains are observed in the shear plane. Especially the side receives the cut of guillotine, the size of recrystal grain is very thin, corresponding with the recrystal grains obtained by cold rolling at 80% deformation rate.

结果表明：经剪切变形后，切面处形成一种独特的带状变形孪晶和蜂窝状变形组织，且存在挤压、扭折等多种变形机制的作用；合金在550 ℃退火2 h后，切面出现许多再结晶晶粒，且在承受剪床切口的一边再结晶晶粒非常细小，相当于冷轧变形80%后的再结晶晶粒尺寸。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。