查询词典 shaft

Based on the analysis of the hobbing machine workbench structure analyze the reasons of the workbench to radial jumpiness shaft jumpiness over tolerance and point out the removal method of various breakdowns .

在对滚齿机工作台结构进行分析的基础上，对工作台出现径向跳动，轴向跳动超差等故障的原因进行了分析，并指出了各种故障的排除方法。

The method how to separate the radial jumpiness of the large shaft by three-point method to gain the round error in high precision is showed particularly. In the part of diameter measurement, this paper indicates how to standardize the photomicrosensor and shows the way how to use correction signal correct the measure error of the grating system which is used to measure the rotated angle of the wheel in detail.

文中详细论述了在圆度误差测量中，利用三点法分离大轴支承径向跳动引起的测量误差而获得高精度的圆度误差测量值的方法以及直径测量系统中，光电开关测量精度的标定方法和通过构建误差修正函数对实现滚轮转角测量的圆光栅系统的测量误差进行实时修正的方法。

The paper introduced the design and construction process of shaft in karst region.

文中详细介绍了岩溶地区竖井的设计方案、施工过程及技术措施。

Mine shaft raised is the keg of mine production ,move at high speed and word throughout the year.

矿井提升是矿山生产的咽喉，高速运行，常年工作。

The key is a segment of a disk and fits in a keyway in the shaft that is cut with a special milling cutter.

关键是一个磁盘部分，并在与一个特殊的铣刀轴键槽切割适合。

The unique locking bar system prevents the key on the output shaft from tipping in the keyway, eliminating the possibility for key and keyway damage that results in a loss of productivity.

独特的锁闭杆系统，防止输出轴上的键在键槽倾斜，消除了键和键槽损害的可能性及其可能会导致的生产力损失。

The section curve equation of main stirring shaft is obtained by deducting the screw profile curve formation process of the stirring kneader.

用数学方法对搅拌捏合机搅拌轴螺杆外形曲线的形成过程进行了详细的推导，得出了主搅拌轴截面曲线形状公式。

Unique control system: main rotor control from floor-mounted stick and collective through control mixer at base of main mast, then through push tubes in main mast to base of swashplate; last-mentioned is contained within mast and supported by a pushrod in rotor shaft.

独特的控制系统：主要由地面控制转子式棒，并通过控制混音集体在主桅杆的基础，然后通过在主桅杆推管，基十字盘

A latchet has an engagement piece for operation and rotatable about a pulley shaft for the pulley is supported on the base.

在基座上支承有棘轮，该棘轮设置有工作用卡合件，并且该棘轮能以绳轮的绳轮轴为中心旋转。

Usage: suitable for precise lathing of rotor outer circle and commutator that with big shaft diameter and V block can not be used.

用途：适用于V型块无法使用的较大轴径的转子外圆或换向器的精车。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。