查询词典 shaft

It's just a matter of hooking the device to the battery and fixing the sensor and it's metal plate on the end of the prop shaft closest to the transfer box.

这只是一个挂接装置对电池的问题和固定的传感器和它的对金属板支撑底轴最接近交接箱。

It is through frequency conversion power output shaft to change, reduce the input power saving energy.

它是通过变频调速改变轴输出功率，达到减少输入功率节省电能的目的。

According to this problem,the blast-cap construction of Anyang Iron and Steel Company's 200 m3 lime-shaft-kiln was renovated by means of opening holes at the top of the blast-cap for air to flow in to eliminate or control the center engulfment.

针对这一问题，对安阳钢铁公司200 m3竖炉石灰窑的风帽结构进行了改造，采用的措施是在风帽顶部开孔打通中心气流，目的是消除或抑制竖炉石灰窑的中心卷吸。

Disc cell mainly consist of chondrocytes, PTHrP-Ihh negative feedback mechanism can modulate differentiation and maturation of chondrcytes during endocartilage ossification in epiphysis of long shaft bone, but its effect on vertebral development is still unknown.

椎间盘细胞主要由软骨细胞样细胞组成，PTHrP和Ihh形成的负反馈机制在长管骨软骨内骨化过程中对软骨细胞分化和成熟具有调节作用，在椎体和椎间盘的发育过程中的作用仍未阐明。

After the coal mine mine shaft electric cable damage causes,receives an elective shock the accident and fire the gas,the coal dust equipollent especially big accident occurrence more over the electric cable fund invests in a big way.

煤矿井下电缆损伤后，引起触电事故和火灾、瓦斯、煤尘等重特大事故的发生，而且电缆资金投入大。

The azimuth of the host shaft was determined with A set of Eulerian angle (precession angleψ, nutation angleθ, self- rotation angle Φ).

用欧拉角（进动角ψ、章动角θ、为自转角Φ）确定刀具主轴方位。

To the horizontal large main arbor , it is key to solve the inconvenience of fit, adjust and maintain evocable by the weight of shaft.

对于卧式布置的大型主轴，结构设计上要在保证主轴达到精度要求的条件下，着重解决因自重而引起的安装、调整、维修不便的问题，若重视不够，将使机床不能正常工作。

The risk factors of cost estimation in the shaft excavation engineering by project management are analyzed in this paper.

对实行项目管理的井巷掘进工程中成本估算所存在的风险因素进行了分析，针对不同的因素提出了相应的改善措施。

By the action of high roatry speed,excentric shaft connection intensifies the fatigue failure of drill tool .

为了达到较好的防斜目的，必须增大钻进时钻头的转速，在高转速的作用下，偏轴接头加剧了钻具先期疲劳失效。

In order to reduce the axle journal of mechanical strength loss, grinding the shaft seating surface wear uneven Department just to Polish it, and then to the journal after Polish excircle size, choose a higher wear resistance ZQAl7-1.5-1.5 bronze, confecting a plain bearings again, replacing the original linear ball bearing.

为了减多轴颈的板滞强度吃亏，磨削的尺寸以轴颈表背磨损不服处恰好磨平为好，再以磨平后的轴颈外方尺寸为基准，采取耐磨性能较矮的ZQAl7-1.5-1.5青铜合金，从头配制一只滑动轴承，替代本来的曲线滚珠轴承。

Hanna: That's over now, isn't it?

都结束了，对吗

You must be ill. You look so pale.

你一定是病了，你的脸色苍白。