查询词典 shaft

It was concluded that the degradation of lube oil was caused by the leakage of K2CO3 caustic liquid resulted from the damaged mechanical seal, low sealing water pressure, high liquid level of dripping sum, poor heat radiation of the shaft seal of lean liquid pump and large space of shaft protection ring etc.

分析了中原大化集团合成氨装置贫液泵润滑油系统滤油器压差迅速升高的原因，指出主要是机械密封损坏或密封水压过低、滴水槽液位过高、贫液泵轴封散热不好、轴承护圈间隙过大等，从而使K2 CO3漏入碱液润滑油系统，导致润滑油变质。

When the bottom plate side syndiospecific lower than a sizzling, drawing pressure ball left, paper will go on there which would in turn low-speed machines brace will receive the same fault because plate following fulcrun is the eccentric shaft, corrected, you can add the eccentric shaft, convex to reverse some of the panels to fan-shaped with a sizzling plane are equal to the maximum State, low-speed machines la along two concave iron support, you can set the concave iron spare, Planer to some, is equal to the thickness to brace the distance below the iron plate plane, the installation at a later time.

当侧规底部扇形不活矮于铁不活立体时，不推纸压球压下去此后，纸弛不离会出不隐凹下下去不隐象，矮速机的不推条也会出不隐同样的障碍，因为扇形不活底下的支点是公道小轴，在校侧时，可以不兵公道小轴的凸背回旋一些，调度到扇形不活背同铁不活立体不等为最好状况，矮速机的不推条是由二块凹形铁撑持，可以不兵凹形铁拆上去，用刨床刨去一些，刨去的厚度即是不推条矮于铁不活立体的间隔，安设此后再举不静调度。

The article analyses the existing calculation method of pin shaft joint partial strength, study the finite element modeling problem of pin shaft joint in girder structure and specific calculation procedure.

分析销轴联接局部强度现有计算方法，探讨梁杆结构中销轴接头的有限元建模问题及具体的计算过程。

To the femoral neck fracture with neck-shaft angle of less than 135 degree, the fixation with the entry angle of less than 135° can make the neck-shaft angle rising, meanwhile, lag screw's location is easier to trend to the inferior of femoral head, displacement and angle between fracture surfaces satisfy the demand of functional reduction or extroversion reduction, and a satisfied stability is performed in biomechanical test.

对于颈干角小于135°的股骨颈骨折，以低于135 °的进钉角度固定时，能增大颈干角，同时拉力螺钉的位置更容易偏向股骨头颈的中、下部，骨折端的位移、成角也能够符合功能复位的要求，在力学测试中表现出较好的稳定性。

The main shaft drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.

这样，普通织机应具备两根轴，主轴驱动筘座并通过齿轮驱动另一根轴。

Thus a normal loom has two shafts. The main shaft drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.

这样，普通织机应具备两根轴，主轴驱动筘座，并通过齿轮驱动另一根轴。

The main body mechanism includes casing, screwed cover plate, upper lifting hook, non-return gear set and chain wheel set inside the casing, and cable clamping board assembly to avoid outer separation of the chain. The ratchet spanner mechanism has ratchet handle assembly fitted to the gear shaft, and the ratchet handle component of the mechanism is patched with gear shaft.

主体机构包括主体外壳和螺接在主体外壳下部的主体盖板，上吊钩配接在主体外壳上部；主体外壳内置防逆转的齿轮传动装置和链轮传动装置，两吊钩的开口部位装有防止链条外脱的卡索板组件；棘轮扳手机构中的棘轮手柄组件配接齿轮轴。

The bearing is fixed on the shaft by setscrews in the inner ring, eccentric locking collar or adapter sleeve so that it decreases the precision requirement of the shaft and makes installment and replacement convenient.

带座外球面轴承的内径采用&+&公差，与轴形成间隙配合，通过内圈上一侧的顶丝、偏心套或紧定套，把轴承固定在轴上，降低了对轴的精度要求，安装或更换轴承极为方便。

The stress and strain concentration region of the shaft sidewall under the three loads,and the correctness of lyophobic additional force theory is demonstrated.It can guide the shaft sidewall design theory and the determination of strengthening region.

确定了立井井壁在这三种荷载综合作用下的应力、应变集中区，论证了井壁破坏理论中疏水附加力理论的正确性，对井壁设计理论以及加固区域的确定提供了一定的理论指导。

The driving shaft causes the spider to rotate,and the other two trunnions of the spider cause the driven shaft to rotate.

驾驶轴原因蜘蛛旋转，另外两个trunnions蜘蛛导致从动轴旋转。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐