查询词典 shaft
- 与 shaft 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Automobile Clutch in the engine and gearbox between the flywheel shell, with screw will be fixed in the clutch assembly after the plane of the flywheel, clutch gearbox output shaft is the input shaft.
摘要汽车离合器位于发动机和变速箱之间的飞轮壳内,用螺钉将离合器总成固定在飞轮的后平面上,离合器的输出轴就是变速箱的输入轴。
-
When the clutch is energized the output shaft is driven; and when the clutch is disengaged and the brake is energized, the output shaft stops.
当电流通过离合器时,出力轴被带动,当离合器分离时,刹车有电流通过时,出力轴就停止。
-
A new method of improving shift quality of AMT with the fuel stop valve was indicated, the efforts to the shift quality at different input shaft and output shaft of clutch were analyzed, the control strategy was established, and the test on one kind of AMT heavy truck was conducted. The test result showed that it could decrease the rotational speed between the drive part and the driven part when clutch was locked, and improve the shift quality of AMT with control of the fuel stop valve.
提出了利用断油电磁阀改善AMT换挡品质的方法,分析了断油电磁阀不同断油和供油时刻对换挡品质的影响,制定了断油电磁阀的控制策略,并在装有AMT的某重型载货汽车上进行了试验,试验结果表明,换挡过程中通过控制断油电磁阀,可以减小离合器接合时主、被动部分的转速差,显著改善了AMT的换挡品质。
-
Through the intermediate gear Z12, the elevator shaft's gear Z13 and shaft are driven to turn, then via friction cone clutch or planetary mechanism the drum obtains six hoisting speeds.
a、冲击钻进:将变速箱右手柄板至&卷扬&位置,变速箱Ⅲ轴齿轮Z8与Ⅳ轴的齿轮Z10啮合,经中间齿轮Z12带动升降机轴上齿轮Z13及轴旋转,通过锥形摩擦离合器或游星轮机构使卷筒获得六种提升进度
-
Project content:According to the market demand,expand production of Four-star、and star series bike parts: front shaft、back shaft 、bike pump、front fork、steel ball、chain、chainwheel crank、cold patch glue、glue and other products for all kinds of bikes.
二、项目内容:根据市场需求,扩大生产&佛斯特&、&四星&、&恒星&牌系列自行车中轴、前后轴、飞轮、链条、曲柄、胶水、前叉、钢珠、打气筒等产品。
-
The input shaft is arranges so that only the driving gear and the rim are accommodated inside the housing while the splined portion of the shaft protruding from the transmission carries the hub of the clutch driven disk.
输入轴这样布置以便只有主动齿轮和齿圈安装在箱体内,而伸出变速器外的轴的花键部分用来支承离合器从动盘毂。
-
Through the retrofit for multi-frequency regulation, shaft seal ing water system,rotator material and shaft cover orientation mode of 150 NW-78×2 low pressureheater drain pump,pump corrosion at low-load operation,bad packing seal,bearing vibration,bearing burned have been solved.
通过对150 NW 78×2型低压加热器疏水泵进行变频调节改造,对轴端密封水系统、转子部件材质和轴套锁母定位形式进行了改进,消除了给水溶氧超标、轴承振动超标和轴承烧毁等缺陷,提高了泵组健康运行水平。
-
The influence of the eccentricity mass moment, position of mass center and the bearing stiffness to the vibration characteristics of the rotor system is discussed in detail; 3. To verify the exactness of FEM and learn the principle of vibration of dredge pump further, The orbit of the rotor shaft of the pump in the dredger is measured, the measurement results show: the repeat of the orbit of the rotor shaft is very bad when dredge pump is in the dredging mud condition.
模态分析确定了泥泵的振动特性;谐响应分析确定了泥泵转子轴在偏心力的作用下轴截面处的最大响应位移;研究了转子轴的质心位置、轴承刚度和质量偏心矩对转子轴振动特性的影响; 3、采用轴心轨迹法,实船测量了泥泵轴工作时振动响应值。
-
In Fig.1,spindle A is supported by two identical isotropic bearings in radial direction;spindle A and drill clamp C–D is connected by shaft B;micro-drill E–F is fixed in the clamp D.Drill part with the screw slots is taken as uniform shaft F by equivalent of the bending stiffness.
In ,主轴A是帮助的两个相仿的各向同性轴承径向目标;主轴A和操演钳的C - D的贯串轴B组;微型钻电子F是牢固在钳4钻局部螺钉插槽是采用调和轴F很是卷曲stiffness。
-
In Fig.1,spindle A is supported by two identical isotropic bearings in radial direction;spindle A and drill clamp C D is connected by shaft B;micro-drill E F is fixed in the clamp D.Drill part with the screw slots is taken as uniform shaft F by equivalent of the bending stiffness.
In ,主轴A是支持的两个相同的各向同性轴承径向方向;主轴A和演习钳的C - D的连接轴B组;微型钻电子F是固定在钳4钻部分螺钉插槽是采取统一轴F相当弯曲stiffness。
- 相关中文对照歌词
- Big John Shaft
- Shaft
- Shaft
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。