查询词典 shaft furnace

Connect joint of mechanical seal with shaft seal water pipeline (For newly installed shaft seal water pipelines, please clean up or rinse out sundries such as welding dregs, sand which are remnantin pipelines in advance). Start shaft seal pump, unclose shaft seal pipeline valve and turn pump shaft by manpower, if leakage, that indicates dunghill exist on shaft seal end-cover, here gland bolts should be loosened to wash mechanical seal with clean water and then impact gland.

将机械密封的接口连通轴封水管路（新安装的轴封水管路应事先将残存在管路内的焊渣、泥沙等杂物清理或清洗干净），启动轴封泵、打开轴封水管路阀门，人工转动泵轴，如有滴漏现像说明轴封端面有脏物存在，应将压盖螺栓松开用清水冲洗机械密封后，再将压盖压紧。

Main product: Ion implanter, Diffusion/Oxidation furnace, Plasma etching system, PECVD, High temperature sintering furnace ,MOCVD, Vaccum furnace, Silicon crystal growing furnace, Electronics industry kiln and furnace ,Solar cell, Pressure sensor.

主要产品：离子注入机，扩散/氧化炉，等离子刻蚀机，PECVD，高温烧结炉，MOCVD，真空炉单晶炉，电子工业窑炉，压力传感器等。

The roller furnace pot uses the 1Cr18Ni9Ti stainless steeliness circled to columnar, or uses the chromium manganese nitrogen refractory steel casting, one side bearing spider outside the furnace body supporting, and uses the electric motor belt speedreducer to carry on the passing-use, to cause the furnace pot to revolve slowly, the work piece causes it heating along with drum furnace pot revolving evenly, and work piece mutually between non-cover phenomenon, after heat treatment, the luster is consistent, furnace pot another end is a feeding head,by two trolley supporting.

滚筒炉罐采用1Cr18Ni9Ti不锈钢制成圆柱型，或采用铬锰氮耐热钢铸件，一端由轴承支座在炉体外支承，并采用电动机带减速机进行传用，使炉罐缓慢旋转，工件随滚筒炉罐旋转使之受热均匀，并且工件互相之间无复盖现象，热处理后色泽一致，炉罐另一端为进料口，由二只滚轮支承。

I coal-fired plant for the production of industrial furnaces, the level of reciprocating grate, grate chain, gas stoves, for use in metallurgy, mining, electrical and mechanical , Chemicals, light industry, building materials industries such as steel rolling furnace, forging furnace, annealing furnace, drying furnace, continuous furnace,.

我厂生产工业炉窑燃煤机，水平往复炉排，链条炉排，煤气发生炉，使用于冶金，矿山，机电，化工，轻工，建材等行业的轧钢炉，锻造炉，退火炉，干燥炉，连续加热炉，。

Using a drum Cr18Ni9Ti furnace tank made of stainless steel cylinder, or a Cr-Mn nitrogen heat-resistant steel castings, by the end of the furnace body, bearing bearing supports, and with a motor-reducer for use furnace tank to the slow rotation, with drum parts Rotation of the tank furnace heated evenly, and the workpiece between each other without coverage phenomenon, the same color after heat treatment furnace can feed the other end to the mouth from two roller bearing.

滚筒炉罐采用1Cr18Ni9Ti不锈钢制成圆柱型，或采用铬锰氮耐热钢铸件，一端由轴承支座在炉体外支承，并采用电动机带减速机进行传用，使炉罐缓慢旋转，工件随滚筒炉罐旋转使之受热均匀，并且工件互相之间无复盖现象，热处理后色泽一致，炉罐另一端为进料口，由二只滚轮支承。

Now the company owns many kinds of products such as YLL vertical cylinder and box coal fuel heating furnace, YYL vertical oil fuel heating furnace, YYW horizontal oil fuel heating furnace and molten salt heating furnace, large heat energy factory by burning waste wood, burning furnace and so on.

现有YLL圆筒型、方箱型燃煤加热炉； YYL立式型燃油燃气、YYW卧式型燃油燃气加热炉，熔盐炉，大型燃废木料热能工厂、焚烧炉等产品，本公司还可以为顾客专门设计制造有其他特殊要求的热载体炉、导热油、热油泵。

Our company mainly produces and sells: Semi-continuous tri-chambers magnetic field vacuum heat-treatment furnace production line, large-size pit gas carburizing furnaces, atmosphere protecting combined furnace groups, vertical aluminum alloy quenching furnaces, stepping box resistance heating furnace, band material finishing continuous heat treatment furnaces, pre-pumped vacuum furnace, High-precision box tempering furnace, etc.

公司主要生产、销售：半连续三室磁场真空热处理炉生产线、大型井式气体渗碳炉、气氛保护联合炉组、竖式铝合金淬火炉、步进式箱式电阻加热炉、带材光亮连续热处理炉、真空预抽炉、高精度箱式回火炉等。

Second, Pyrometallurgical, available blast furnace, shaft furnace, rotary furnace, reverberatory furnace and take them two or three kinds of combination, but there are common problems in the smelting process, the emissions of a large number of products containing lead, sulfur dioxide and other harmful ingredients dust smoke, dust need to configure the corresponding device.

二，火法，可用高炉，竖炉，旋转炉，反射炉，把他们两个或三个种的组合，但也有在冶炼过程中常见的问题，一个含有铅，二氧化硫大量产品的排放量，其他有害成分粉尘烟尘需要配置相应的设备。

On the basis of this model, combined with potential flow for expressing burden flow, considered with gas-solid heat exchange and main chemical reaction in shaft furnace, Comprehensive two dimensions mathematics model of shaft furnace is set up for analyzing flow, heat and mass transfer in furnace.

并在此基础上，结合反应固相流动的势流模型，综合考虑气固传热和竖炉内的主要化学反应，建立了竖炉二维综合数学模型，对炉内流动、传热及传质过程进行了解析。

In terms of the transmission shaft balancing, it exists another problem that the shaft is not looked at as rigid body.When the rotor running at a high-speed ,under the action of unbalance force ,the transmission shaft will bend. It is certainly ideal to balance a transmission shaft as a flexible rotor.However, considering the mass production of automobiles, this method is obviously unpractical. In order to discreasing the flexible deformation, in this theory, the feasibility that double- plane balancing takes method the place of multi-plane balancing on a special place for one segment transmission shaft.

从传动轴平衡的角度来看，传动轴并非刚体，在汽车高速旋转时，由于不平衡力的作用会使传动轴发生挠曲，如果将传动轴作为挠性转子进行平衡当然比较理想，但是不符合汽车大批量生产的实际，为减少挠曲振动，利用挠性转子平衡原理，对于单根传动轴，从特殊位置进行校正，从而以二面平衡代替多面平衡是可行的。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。