英语人>网络例句>section paper 相关的网络例句
section paper相关的网络例句

查询词典 section paper

与 section paper 相关的网络例句 [注:此内容来源于网络,仅供参考]

The paper discussed the protection of incoming section and lightning protection of transformer in view of protection function of lightning arrester in 220 kV substation,and proposed feasible and detail means for operation maintenance.

从220 kV变电所内避雷器的保护作用、进线段的保护、变压器的防雷保护等几方面进行阐述。

This paper gives an exact solution for free vibration of a physically nonuniform straight bar with vary-ing section by the use of a class of integrable linear ordinary differential equation.

本文应用可积的一类线性微分方程求出了非均质变截面弹性直杆振动问题的一个精确解,我们应用这一精确解验证了渐近解的精确度。

In the last section, this paper will reconstruct the LIS education of China in the new millennium.

第四部分,论文对新时期中国图书馆学情报学教育的进行构想。

After describing the background and condition of local autonomy, the author discusses the material administration of local government, and this part is the main section of this paper.

在界定地方自治的历史背景与外部环境之后,文章论述地方社会与政府机构的具体运作与治理方式,这是本文的主体。

Firstly, this paper introduce the present and prospective development, moreover compared advantage and short of different roll forming theory. Subsequently simplified process and analyzable model of channel section according to deforming elastic-plastic macro deforming finite element theory.

本文首先介绍了国内外关于辊式冷弯成型理论研究的现状与发展趋势,并比较了各成型理论的优缺点,随后在分析槽钢辊弯成型特点及其变形规律的基础上,以弹塑性大变形有限元理论为基础,对槽钢成型过程做出合理简化,建立分析模型,利用MARC软件对槽钢辊弯成型进行了三维有限元数值模拟分析。

So the next time you read the entertainment section of the paper, treat it as if you are reading one of those gossip mags.

所以下一次当你们读到报纸的娱乐版,你们可以象对待八卦杂志一样,不要相信!

In this paper it is given a more effective formula about the direction angle of the main plane in the plane stress state.2. To introduce the principle and method for drawing 3-D graph with the compuer and for checking up with the computer cursor,to give outline of expressions of 3-D curve,outline of cursor meterage of well depth,well deflection angle and direction angle at any section.

介绍了在实践中总结出的计算机绘制与光标检测3维图形的原理和方法,给出了3维动态图形到屏幕坐标的变换式、各测点的平滑连接方法以及描绘与检测井眼轨迹曲线的典型应用,实现了空间井眼轨迹曲线的任意旋转、投影和给出了任一井段的井深、井斜角和方位角的光标检测软件。

At first step, the processor before the deformable body contact the end face of cone die cavity regarded as an extrusion process. The minification of core boss's cross-section regarded as compressibility of direct extrusion, which acted as definition factor when construct the Direct Extrusion Model element. Another step, the model element of flat punch extrusion on wedge piece process was constructed when propose the process of deformable body overflow die corner. In this way the spherical end face of blank looked as cone end face one, t he approximate treatment is one of originality innovation in this paper. At last, the two elements have been connected and constructed the model element of cone boss part's deformation in the open die forging.

对于锥形凸台成形的第一个特征时段,即坯料和锥形凸台型腔的端面接触之前的变形过程,本文将凸台的截面缩小率转换成挤压成形的压缩率并以此为界定,建立了不同截面缩小率时的锥形模正挤压的模型单元;对于锥形凸台成形的第二特征时段即锥形模的角部充满过程,在详细考察锥形型腔端面对变形过程影响的基础上,将变形体的球形端面近似成锥面建立了平冲头挤压楔形体的模型单元;最后将前述两种模型单元有机连结,构建了开式模锻中整个锥形凸台成形过程的定量描述。

In this paper, the minimum excess principle and its method are used in dynamic analysis of variable section beam .

本文应用最小余能原理的理论和方法确定变截面杆的固有频率。

The paper derives detailly the viscoplastic strain velocities of joint, intact rock, as well as multilaminate rock mass corresponding to different stress states, and presents a viscous elastoplastic F·E·M·with consideration of the stepwise excavation sequence and different supporting time of lining in underground works with large cross-section.

分别推导了在不同应力状态下节理面、完整岩石和多组节理岩体粘塑性应变速率的计算公式。提出了节理岩体大断面洞室考虑分步开挖和不同支护时间的粘弹塑性有限元数值方法。

第18/42页 首页 < ... 14 15 16 17 18 19 20 21 22 ... > 尾页
推荐网络例句

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时,滚道或滚动元件褪色是很常见的特征。

The lawyer's case blew up because he had no proof.

律师的辩护失败,因为他没有证据。