查询词典 secondary axis

The error analysis shows that the present indexing method seems to be available to the cases of the zone axis both parallel and inclined to the optical axis of SEM.

误差分析表明，本注释方法不但适用于晶带轴平行于扫描电镜光轴的情况，而且适用于晶带轴倾斜于光轴的情况。

Taper Lock Bushes coupling is using the conical cuniform function to couple the axis and hub,which is applied in the coupling between axis and triangle pulley,flat pulley,synchronization gear,chain wheel,clutch.

锥套联接是利用锥面的楔形作用实现轴和轮毂的联接，它适用于三角带轮、平皮带轮、同步齿形带轮、链轮、联轴器等部件与轴之间的联接。

The fast axis of the quarter-wave plate is parallel to the dynamically induced birefringent axis of the photoelastic modulator.

被测1/4波片的快轴与光弹调制器的振动轴平行，且与起偏器和检偏器的透光轴分别成±45°夹角。

An optimal design of the elastic axis based on ANSYS is presented,to meet the design requirement of the tension sensor of the underwater diamond wire saw,The optimal dimension for the least volume of the elastic axis is obtained in the design.

针对水下金刚石绳锯机串珠绳张力传感器的设计需要，提出了基于ANSYS的张力传感器弹性轴的优化设计，建立了优化设计数学模型，分析了ANSYS的优化设计方法，完成了基于ANSYS的弹性轴优化设计过程，最终得到了满足弹性轴体积最小时的优化设计尺寸。

Considering the disturbance of reaction wheel assembly is related with the fixing condition, two methods named 'rigid six-axis test bed' and 'flexible six-axis test bed' were adopted respectively to measure the disturbance. Measurement results of two methods were compared through three aspects.

考虑到反作用轮的扰动与安装条件有关，使用&刚性六分量测试平台&和&柔性六分量测试平台&两种方法进行反作用轮扰动特性测量，并从三个方面对两种方法得到的结果进行比较。

The attitude control system is compared with a micro momentum-biased reaction wheel and three-axis magnetic-coil, to realize the followingfunctions:(1) after release from launcher, by B control law, this mode can damp the body rate down;(2) After that ADCS switches to the three-axis-stabilizing mode.

姿态控制子系统，以俯仰偏置动量轮组合三轴磁力矩器构成控制系统主体，实现初始入轨后的姿态角速率磁控阻尼，以及姿态的三轴稳定控制；分别对动量轮和三轴磁力矩器进行了参数设计。

The calculation of principal axis box includes the school of the school pit, principal axis of the school pit, key of the school pit, bearings of the school pit, stalk of school pit, wheel gear of rubbing the clutch to calculate calculate etc.

主轴箱的计算包括摩擦离合器的校核、齿轮的校核、轴的校核、轴承的校核、键的校核、主轴的校核计算等。

The calculation of principal axis box includes the school of the school pit principal axis of the school pit key of the school pit bearings of the school pit stalk of school pit wheel gear of rubbing the clutch to calculate calculate etc.

主轴箱的计算包括摩擦离合器的校核、齿轮的校核、轴的校核、轴承的校核、键的校核、主轴的校核计硕羧。

In a preferred embodiment, the guiding track is annular and is bounded by a circular cylindrical rolling surface (51) of the rolling track and a roller (35) of the driving member, said roller being rotatable about an axis of rotation (37) coinciding with a common central axis (39) of the guiding track and the rolling track.

在优选实施例中，导向轨道是环形的并且被滚动轨道的圆柱形滚动表面（51）和驱动件的辊子（35）限定，所述辊子能够绕着大致与导向轨道和滚动轨道的公共中央轴线（39）重合的旋转轴线（37）转动。

Wire resistive touch screen technology, the grass-roots to the voltage field in both directions through the precision resistor networks are added to the work of conductive glass surface, we can simply be understood as the voltage field in both directions of staggered working hours added to the same work surface, The outer layer of Ni-Au conductive layer is only just be used as a pure conductor, there are time-test, after touching the inner ITO contact point X-axis and Y-axis voltage value method measured touch point position.

五线电阻技术触摸屏的基层把两个方向的电压场通过精密电阻网络都加在玻璃的导电工作面上，我们可以简单的理解为两个方向的电压场分时工作加在同一工作面上，而外层镍金导电层只仅仅用来当作纯导电体，有触摸后分时检测内层ITO接触点X轴和Y轴电压值的方法测得触摸点的位置。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。