查询词典 secondary axis

The eyepiece has an optical axis , and this axisshouldbe aimed at the center of the main mirror for best performance - though in practice it is the center axis of the focuser drawtube that you aim at the primary mirror .

目镜和主镜一样也有光轴，光轴应该对准主镜的中心--尽管实际上，目镜的光轴对准的是调焦筒的中心。

The computer separately connects and controls the I/O end and A/D converter; the I/O end connects and controls the X, Y axis driving circuit and the semiconductor laser; the X, Y axis step-by-step driving circuit connects and controls the X, Y step-by-step electrical machines to control the dimensional platform; the beam of the semiconductor laser passes through the focusing drawtube with 0.1mm diameter to form the facula with the diameter less than 0.1mm; the facula irradiates on the detector surface of the XY dimensional displacement platform to produce the corresponding electric signals; the detector surface connects the A/D converter through the amplifier; the electrical signal is amplified and is converted into the data signal by the A/D converter and is sent to the computer for processing.

由计算机分别连接并控制I/O端口和A/D转换器，I/O端口分别连接并控制X、Y轴步进电机驱动电路和半导体激光器，X、Y轴步进电机驱动电路分别连接并控制X、Y轴步进电机，从而控制二维位移平台，半导体激光器的光束经过设有直径0.1mm小孔的聚焦镜筒形成＜0.1mm直径的光斑，光斑照射于设在XY二维位移平台上的探测器表面使其产生响应的电信号，探测器表面经放大器连接A/D转换器，电信号经放大器放大后，由A/D转换器转换为数据信号送计算机处理。

Similarly, the cotton root-length density reduced gradually from the root axis to both sides of it, and the maximal length density of root was observed at the position of root axis in soil and was diminished by increased dripper discharge.

水平方向上，棉花根长密度由根轴向两边逐渐减小，而且根轴处的根长占总根长比率随滴头流量的增大而变小。

In order to achieve the setting up angle should be monitored and debugged, a new approach is brought up. With the CCD receiving the focusing spot of parabolic mirror, while rotating the parabolic mirror, collecting the focusing spot location information, the eccentric angle between the optical axis and the structural central axis could be found. System principle and design have been studied.The experimental results meet the need to test and monitor to the setting up angle of the discal parabolic mirror.

为了实现对抛物面反射镜的装配角度进行监控和调试，提出了一种通过CCD接收回转抛物面镜的聚焦光斑，同时旋转抛物面镜，采集光斑重心位置信息，从而计算出光轴与结构中心轴之间的偏心角的实现方案，并从方案原理和设计上对其进行研究和实验，实验结果证明该系统能应用于对盘状抛物面反射镜装配角度的测试和监控。

The exchange of the electrovalence of the cupric ion has been testified by XPS-ESCA.Graphite and chloride in the stage structure,seem to be the conductor and insulator,which form the "sandwich" structure.This special structure produced a weak chemical bond belt and provided the carrier space in the perpendicular direction to the c-axis.These factors in and vertical to the direction of c-axis together increased the electrical properties.

GICs将良导体的石墨层与绝缘体的氯化物层在分子尺度上结合起来，所形成的阶结构相当于许多导体和绝缘体层组成的"三明治"结构，产生化学键薄弱的通道，提供了垂直c轴方向的载流子通道，隧道效应和格架空间提供了载流子活动空间，这些因素共同作用使得GICs的电导率成倍增加

The true action is only to be secured when the amount of ellipticity is exceedingly slight, the centre of motion of the revolving piston-shaft being in a line intersecting the minor axis, at about one-third of the length of such an axis.

真正的行动只是被担保的数额时，椭圆是非常轻微的，该中心的议案，旋转活塞轴正处于一条线相交的轻微轴，在约三分之一的长度，例如一轴。

Sonographic examinations of the pancreas were performed by sagittal scanning at the epigastrium; the long axis and short axis of the oval cross-sections of both the pancreatic head and body were measured.

检查测量的方式是在上腹部作纵向扫描，可以分别得到胰脏头部与体部之圆形纵切面造影，进而分别测量胰脏头部与体的长轴与短轴，一共为4个胰脏因数。

All kinds of errors that influence load sharing characteristics of gear system have been given, mainly including manufacturing and assembly error of each gear component's axis and each bearing's axis, tooth thickness error. The formulas of equivalent mesh error have been derived.

确定了影响行星齿轮传动系统均载特性的各类误差，主要包括：各个齿轮构件的中心轴线制造和安装误差、轴承中心轴线的制造和安装误差、行星架的制造误差、齿轮的齿厚偏差。

InWürth's scheme, it is stays identical with the main axis, whereas inEvert's scheme, it is excentric from the common axis and rotates aroundit with an angular speed depending from the cogs'ratios.

在沃思的计划，这是保持一致的主轴，而在埃弗特的计划，这是偏心的共同轴和它周围旋转的角速度而从螺丝钉'的比率。

First, the wheelset is fixed and rotated by the device used hi vehicle depot as usual. Second, the center line of wheelset axis is determined by a device called axis-center probe. Last, the acting device for sensor can draw a whole felloe profile, which is made up of parallel-pole device and rotating-probe.

鉴于此，本文给出了一种全新的测量方案：采用车辆段普遍使用的转轮器实现被测轮对的定位；采用车轴基准探尺测定被测轮对的轴线；采用并联式伸缩机构和旋转测头作为传感器的执行机构，测定轮辋断面的轮廓线。

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"