查询词典 seal of

By now, the honeycomb seal, brush seal and finger seal are three kinds of the most prospective seals.

目前，除了梳齿密封外，蜂窝密封、刷式密封及指尖密封是三种最有前景的密封。

Mechanical seal assembly: In the dynamic and static loop mirror coating on the 20th floor cleaner lubricants; add lubricant bearing guided, first gently positioning ring static load bearing guide; longer shaft add the oil, the mechanical seal part of the dynamic ring gently into the shaft, the hand-push retractable seal ring should be able to freely (Note that dynamic and static part of the anti-ring to the assembly site to be in place).

机械密封装配：在动、静环镜面上涂一层洁净的20号润滑油；导轴承座抹上润滑油，先把静环轻轻定位装入导轴承座；再在泵轴上抹上润滑油，把机械密封的动环部分轻轻装渗透泵轴上，用手轻推密封环应能伸缩自如（注意动、静环部分的防转部位需装配到位）。

Mechanical seal assembly: In the dynamic and static loop mirror coating on the 20th floor cleaner lubricants; add lubricant bearing guided, first gently positioning ring static load bearing guide; longer shaft add the oil, the mechanical seal part of the dynamic ring gently into the shaft, the hand-push retractable seal ring should be able to freely (Note that dynamic and static part of the anti-ring to the assembly site to be in place).

机械密封装配：在动、静环镜面上涂一层洁净的20号润滑油；导轴承座抹上润滑油，先把静环轻轻定位装入导轴承座；再在泵轴上抹上润滑油，把机械密封的动环部分轻轻装入泵轴上，用手轻推密封环应能伸缩自如（注意动、静环部分的防转部位需装配到位）。

Mechanical seal assembly: In the dynamic and static loop mirror coating on the 20th floor cleaner lubricants; add lubricant bearing guided, first gently positioning ring static load bearing guide; longer shaft add the oil, the mechanical seal part of the dynamic ring gently into the shaft, the hand-push retractable seal ring should be able to freely (Note that dynamic and static part of the anti-ring to the assembly site to be in place).

机械密封装配：在动、静环镜面上涂一层洁净的20号润滑油；导轴承座抹上润滑油，先把静环轻轻定位装入导轴承座；再在泵轴上抹上润滑油，把机械密封的动环部分轻轻装入泵轴上，用手轻推密封环应能伸缩自如（注重动、静环部分的防转部位需装配到位）。

Stirring drive the use of seals and seal cutting gas seal, sealing ring and seal combination of anti-threaded to ensure that materials do not leak powder

搅拌传动密封和切割封采用气密封，密封圈密封及反螺纹密封相结合的方法，确保细粉料不泄露。

In the beginning of the study, the related data of LNG's cold energy and recycle system for shaft seal gas were collected, then those were applied to the software for simulated process to calculate the related parameters of LNG's cold energy. Acquired parameters can be used to establish a simulated process system for recycling shaft seal gas, and the sequential, influential factors and results between LNG's cold energy and recycle system for shaft seal gas can be discussed immediately.

研究初期收集LNG能与轴封气回收热交换器主要操作相关据，应用制程模拟软体计算LNG能相关据，建轴封气回收热交换器系统之制程模拟系统，随即探讨LNG能与轴封气回收系统之一影响相关因素与结果。

A front-back seal ring structure is adopted in the pump to prevent the liquid from leaking from the high-pressure area to the low-pressure area. The front seal ring is mounted on the pump body while the back seal ring mounted on the bearing body. They should be changed when they are so worn-out that they have an effect on the efficiency and self-priming performance of the pump after the operation for a long time.

泵内部防止液体由高压区向低压区泄漏的密封机构是前后密封环，前密封环装在泵体上，后密封环装在轴承体上，当泵经长期运转密封环磨损到一定程度，并影响到泵的效率和自吸性能时，应给予更换。

A front-back seal ring structure is adopted in the pump to prevent the liquid from leaking from the high-pressure area to the low-pressure area. The front seal ring is mounted on the pump body while the back seal ring mounted on the bearing body. They should be changed when they are so worn-out that they have an effect on the efficiencyself-priming performance of the pump after the operation for a long time.

泵内部防止液体由高压区向低压区泄漏的密封机构是前后密封环，前密封环装在泵体上，后密封环装在轴承体上，当泵经长期运转密封环磨损到一定程度，并影响到泵的效率和自吸性能时，应给予更换。

Several effective seal structures are introduced for improving the seal performance of the stretching machine' oil-seal.

为了提高牵伸机油封的密封性能，本文介绍了几种切实可行的密封结构。

The main reason is the unreasonable design of seal has been found out by analyzing the seal problems of the stretching machine' oil-seal.

摘 要：通过对牵伸机油封出现的密封问题的分析，发现其主要原因是密封设计的不合理。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷