查询词典 sea-surface

For thin polycrystalline films, especially those with columnar structure, once the diameter of grains on the film surface is larger than the film thickness, the total area of above and under basal planes (film-substrate interface) will be larger than that of side plane. Therefore besides the minimization of boundary energy in traditional bulk material, surface energy, interface energy would be considered due to the anisotropy of surface energy, interface energy being able to drive the grain growth and texture evolution in thin films.

对于薄膜特别是柱状晶薄膜，当晶粒在膜平面内的尺寸大于膜厚时，柱状晶粒的上底面和下底面的面积将大于侧面的面积，因此薄膜中的晶粒生长除像整体材料中的晶粒生长一样考虑晶界能外，还需要考虑表面能和界面能，因为各向异性的表面能和界面能将导致薄膜中的异常晶粒生长和织构变化。

The computational results indicate that surface catalytic combustion restrains gas phase combustion. Inlet velocity and tube diameters have important influence on catalytic combustion of hydrogen. For smaller inlet velocities,reaction is dominated by gas phase combustion. As the inlet velocity increases,there exist both surface catalytic combustion and gas phase combustion. For bigger inlet velocities,reaction is dominated by surface catalytic combustion. The temperature of flame core decreases with the decrease of tube diameter.

计算结果表明，表面催化反应对空间气相反应有抑制作用；入口速度和管径对氢气的催化燃烧过程有重要的影响，在入口速度较小时，燃烧主要是空间气相化学反应，随着入口速度的增大，燃烧过程同时存在着表面催化反应和空间气相反应两种控制因素，在入口速度较大时，燃烧主要是表面催化燃烧过程；随着管径的减小，微型管道内反应的最高温度降低。

In situ comparison of surface slip deformations showed that the persistent slip bands emerging at the surface was delayed, and the surface deformation homogenized after implantation, an indication of ductility improvement.

各离子注入使试样表面的变形分布更均匀，推迟了PSB's在表面的出现，表明离子注入延长了试样的裂纹萌生寿命。而疲劳断口分析表明，各金属离子注入对裂纹的扩展过程无明显影响。

According to differences among these groups, for est potential fire behavior in Qinling mountains crown fires can be divided into strong crown fire type, weak crown fire type and no crown fire type based on th e maximum crow density of easily burning layers, separated by indices D 0.11 kg/m3 and 0.37kg/m3 respectively; the intensity of surface fire can be d etermined by the μ and W factors and be divided into 3 classes, the str ong surface fire and the medium surface fire, separated by indices W 1.40k g/m2 and indices μ 40%respectively.

据类间 差异性将秦岭森林潜在树冠火行为分为强度树冠火、弱度树冠火和无树冠火3种类型，划分依据为冠层易燃物最大密度，区分指标分别为0.11kg/m3和0.37kg/m3；地表火强度划分应用μ和W双因素判断法，并将其划分为强度地表火、中度地表火和弱度地表火3 种类型，其区分指标分别为地表可燃物载量1.40kg/m2和地表可燃物绝对含水率40%。

The existing stone cutting tool, the tool bit is constituted by the sole grade's grinding material, when cutting the rough stone, the cutting speed is quick, the cutting efficiency is high, but the cutting surface fluctuates in a big way, becomes rough, after the cutting, grind and polishing take long time to do, if use the fine grinding compound, the cutting face is smooth, but the cutting speed is slow, the cutting efficiency is low, therefore the existing stone material cutting tool cannot have the high efficiency to cut the stone which have the smooth cutting surface, in view of this, how to keep the high working efficiency and get smooth cutting surface?

现有石材切具刀头由单一粒级的磨料构成，使用粗料时，切割速度快，切割效率高，但切割面起伏大，变得粗糙，切割后研磨抛光耗费时间长，使用细磨料，切割面较平整，但切割速度慢，切割效率低，因此现有石材切具不能高效率地切割出平整的石材，针对这一现状，如何既能高效率切割，又能使切割面保持平整呢？

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果展开平板在压边圈面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈表面间的平衡块；压边圈的变形。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

褶皱起因于不充分的拉伸或失去控制的压缩变形。如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

PAN-ACF was modified by different methods, such as heat oxidation, nitric acid dipping and hydrogen peroxide dipping, the characteristics changes of the PAN-ACF before and after modification such as kinds of surface functional groups, amounts of oxygen function groups, surface microstructure and specific surface were analyzed by FT-IR, Boehm.

采用热氧化、硝酸浸渍、过氧化氢浸渍等方法对聚丙烯腈基活性炭纤维进行改性处理，使用FT-IR、Boehm滴定法、SEM、BET等分析技术表征了改性前后PAN-ACF表面官能团种类、含氧基团数量、表面微观结构及比表面积等表面特性。

When ethanol goes into the red blood cells, osmotic pressure changing causes the cell vertices moving to the center, and double-concave disc surface will be the spherical one. It results in the red blood cell volume larger and surface area smaller, causes the ratio of the surface area and volume significantly decrease, and the resistance tensile capacity of red blood cells reduced.

分析认为乙醇进入红细胞后，由于渗透压的变化将使细胞顶点向中心移动，双凹形的圆盘曲面将向球形细胞转变，导致红细胞体积变大和表面积的减少，引起红细胞表面积和容积的比值显著变小，红细胞的抗张能力降低。

He paid $5,000 for this cupcake.

他我这个纸杯蛋糕花了5000美元。

I mean, if you want to, that is

我的意思是，如果你们想吃的话。