查询词典 screw

To use the 1 style screw adjust down the screw, and until hitting cultch of the turret head to continue full change tool.

再用一字螺丝起子往下调整螺杆，直至撞开离合器六角刀塔连续换刀为止。

The right femur specimens were fixed with DHS augmented by bone cement, as the augmentation group The screw track of femoral neck was expended by curette, and the femoral head facing upwards were injected with 2 mL low viscosity bone cement. Then lag screw was wrested to keep the position unchanged till the bone cement coagulated.

右侧标本行骨水泥强化DHS固定（在股骨头近端钉道用刮匙扩大，股骨头朝下，注入2 mL低黏稠度骨水泥，拧入拉力螺钉，保持位置不变直至骨水泥凝固。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder ,Higher stick of resin material ,higher screw back pressure. Screw speed differs depending

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大

On decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin,higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75

但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大

On the basis of introduction of an epicycloid parameter,δ,an equation is derived for cycloid and its screw surface in screw pump.

本文在引入外摆参量δ的基础上建立了螺杆泵摆线和摆线螺面的方程，并通过对δ的研究，提出了螺杆泵的部分设计理论。

In operation, the screw cylindrical surface and the pump cylinder wall formed between the layer of oil film to prevent direct contact between the metal, so that screw tooth surface wear significantly reduced.

在运行中，螺杆外圆表面和泵缸内壁之间形成的一层油膜，可防止金属之间的直接接触，使螺杆齿面的磨损大大减少。

Our company specializing in the production of dual-cone, double-barrel, screw, double-, double-cone plastic extrusion machines, single screw extruder, plastic pipe production lines, plastic profile production lines, plastic sheeting, sheet production line, plastic extrusion To create materials and production lines dedicated to the production of environmental protection Plastic-wood extruder.

我公司专业生产锥双、平双机筒、螺杆，平双、锥双塑料挤出机、单螺杆挤出机、塑料管材生产线、塑料异型材生产线、塑料板、片材生产线、塑料挤出造料生产线及专用于生产环保塑木的挤出机。

According to the similarity criterion, an experimental model was designed which is one-third of 3500mm heavy and medium plate mill pressure screw-pairs in sizes. Electrometric method was adopted to get the load distribution of the thread layers by measuring the bending deformation of the screw teeth.

依据相似准则，制作3500mm中厚板轧机电动压下传动螺纹副1/3的测试模型，采用电测法获取悬臂螺牙弯曲应变值，模拟实际轧制力和过平衡力作用下螺纹副螺牙各层载荷大小及分布。

To improve the machining efficiency and precision of convex screw s,a new method was put forward for inner whirlwind NC enveloping milling of screw curved surface.

使用轴承测量仪器完成对滚子球基面凸度测量、凸形的判定，确定了测量方法，提高测量的准确性及测量效率。

On the basis of measured data processing,error analysis,curve modeling and object modeling,it establishes the mathematical modeling of the screw parts of single screw compressors.

在测量数据处理、误差分析和曲线曲面造型、实体造型技术的基础上，建立了单螺杆空气压缩机螺杆零件的数学模型。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。