查询词典 screw-driven

An integrated unit of ball screw stripping,ball bearing tapered wedge and fixed-distance pull off was adopted in the design of injection mould for screw plug.

在螺塞注射模具设计中，采用了滚珠丝杠脱模装置和滚珠、斜楔拉模、定距联合装置，利用滚珠、螺母、丝杠及齿轮传动自动拧出螺纹塑件，实现塑件自动脱模；利用滚珠、斜楔、滑块机构拉开定模板和浇口板并控制其拉开距离，从而达到自动生产目的。

Lean the plug to the lowest position while changing oil and screw out, then drain the oil refuse in box, fill new oil after box repositioned, and screw down the plug again.

放油油塞即侧面油塞，注油时旋下，见有油渣出时旋上并拧紧，换油时，将此油塞倾斜至最低位置，旋下，放尽箱内废油，箱体复位后注入新油，再旋上拧紧。

Objective: To investigate the effects of the number of the screw in the dynamic compression plates on the stability of plate and screw structure in vitro.

目的：探讨螺钉数量对骨与钢板螺钉结构系统稳定性的影响，为临床上钢板螺钉内固定应用提供实验数据。

Objective: To investigate the effects of the position of the screw in the dynamic compression plates on the stability of plate and screw structure in vitro.

目的：探讨螺钉位置对骨与钢板螺钉结构系统稳定性的影响，为临床上钢板螺钉内固定应用提供实验依据。

For each nut, and screw all gap exists, but in General, there is no gap and screw.

差每个螺母来说与丝杠都有间隙活命，但是从个体来说与丝杠操纵间隙。

Department specializing in the production of special screw nut screw.

螺丝部专业生产特殊螺丝螺母。

It is common practice to use the same distal locking screw of the nail if this surgery is performed, however, there is a risk of the new drill hole "cutting out" into the old screw hole.

如果手术已经完成，一般会利用相同的远端锁钉，但是，有可能这个新的锁钉孔滑移进入原有的锁钉孔。

All kinds of screw cap, plain cushion, machine screw nail, fiberboard nail and hex wood bolt.

各种螺帽、平垫、弹垫、机螺钉、自攻钉系列、纤维板钉、六角木螺钉等配套。

Therefore, in order to enable the screw to smoke, Pai oil separated from the mouth, the screw thread section of the length of at least larger than a lead.

因此，为了使螺杆能吸、排油口分隔开来，螺杆的螺纹段的长度至少要大于一个导程。从上述工作原理可以看出，螺杆泵有以下优点

Therefore, in order to enable the screw to smoke, Pai oil separated from the mouth, screw thread length is greater than at least one lead.

因而，替了使螺杆能呼、排油口合隔启往，螺杆的螺纹段的少度至多要小于一个导程。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。