查询词典 screw up

The round trip is driven by servomotor, matched up with precision ball screw and wire slide rail, to smooth the round trip of the blade and position accuracy.

切刀与主轴采用无级变速AC马达。5。行程以伺服马达驱动，配合精密滚珠螺杆及线滑轨，切刀行程顺畅，定位精确。

Theoretical models are developed to predict the ultimate up-lift bearing capacity of single-screw anchor in sand, and the calculation formula of them is given.

当两个锚片的间距较大时，其上拔极限承载力与两个单锚片的极限承载力之和相接近，两种计算模式的分界间距是4倍锚片直径。

When the user opens a box the hoisting up, the transformer and the bottom plank connected bolt shall be demolished, hangs with four similar length's steel cable on oil tank's special-purpose lift hook, uses another string or the scallop to bundle these 4 steel cable and the transformer in the same place, pays attention to steel cable and outside stainless steel shell of bellow on the top of the transformer should add the felt circle or the rubber gasket, in order to avoid the steel cable damage transformer 's bellow shell, then slings the transformer slowly, Moves it to the pad base on the support, fix the transformer with the install screw buried well in advance.

5.4用户开箱起吊时，将互感器与底木板相连的螺栓拆除，用四根同样长度的钢缆挂在油箱的专用吊钩上，再用另一根绳子或带子将这4根钢缆和互感器捆在一起，注意钢缆与互感器顶端的膨胀器不锈钢外罩外应加毡圈或橡皮垫，以免钢缆损坏互感器的膨胀器外罩，然后慢慢吊起互感器，把它移至支撑垫基上，用预先埋好的安装螺杆将互感器固定。

CNC Tool: Tool 安威 Taiwan, STANNY fine sebang keep out a knife, BT shank, chuck cutter tube cutter to powerful folder-type holders to extend the pole up discarded fast bit, fine boring holes to fine-tune the system, lock knife Block pull screw bolts, Taiwan Guangjie chuck cylinder rod to extend the handle folder, durable lining Universal milling cutter drill holders, drill chuck Bao Quan, Kyushu, Japan, Japan Institute of precision high-speed SHOEA Dao BORING

数控刀具：台湾AW安威 Evermore粗搪刀刀座，STANNY世邦精粗搪刀， BT刀柄，铣刀把强力铣刀夹头筒夹延长杆舍弃式刀杆舍弃式快速钻头，微调精搪孔系统，锁刀座拉钉螺栓，台湾广杰刀柄延长杆夹头筒夹，耐久搪刀钻铣万用刀杆，铨宝钻夹头，日本九州，日研 SHOEA精密高速刀把镗刀

A new special economical experimental unit which applies to the R717 recurrence system of the screw compressor with the economizer has been designed and set up. The experiential results of the single stage recurrence and recurrence with the economizer, such as refrigerating capacity, shaft power, volumetric efficiency etc, under different conditions are got from the experiments. The author analyze and the calculate results of theory in this paper.

建立了独特节能的R717工质带经济器螺杆制冷循环系统的试验装置，通过对所研究压缩机的试验测试，得到了普通单级螺杆循环和带经济器螺杆循环在各种工况下的制冷量、轴功率、容积效率、相对补气量、中间压力等数据，并与了本文理论计算的结果进行了比较分析。

Unscrew the screw to push the needle up as far as possible and then tighten again - use screwdriver to make final turn to ensure the needle doesn't work loose when sewing .

拧螺钉，推动了针，尽量然后再次收紧-使用螺丝刀作出最后之交，以确保针头不松散，工作时，缝纫。

In order to solve the poor load capacity of oil film bearings during the start-up process of tandem cold rolling mills, based on the hydrostatic bearing theory, a load bearing capacity model for oil film was established. The influences of screw-down tilting, hydraulic pump power and restrictor's hydraulic resistance on the hydrostatic pressure bearing-spindle system were calculated.

针对某CVC带钢冷连轧机启动阶段支持辊油膜轴承静压承载能力不足的问题，应用流体润滑理论，建立了轴承倾斜工作下静压承载能力的全润滑系计算模型，分析了轧机压下倾斜、油泵功率和节流器液阻对轴承静压承载性能的影响。

To meet the demand of higher built-up rate ,single-bending screw drill tool with large angle is used during the drilling of the moderate-and short-radius horizontal well.

钻中短半径水平井，在采用弯角较大的单弯螺杆钻具以满足高造斜率的需要时，由于套管内径较小，螺杆钻具钻头处位移比较大，螺杆钻具能否顺利通过直井段是钻中短半径水平井面临的一个重要问题。

The main products have pressure riveting nut, compression nut riveting columns, inlaid into the nut, rivet nut up, riveting pressure screw, rivet pull screws, loose screws, etc.

主要产品有压铆螺母，压铆螺母柱，镶入螺母，涨铆螺母，压铆螺钉，拉铆螺钉，松不脱螺丝等。

The screw plug of the oil pump must be screwed up after daily work is finished.

5.9 每天工作完成后，必须旋紧油泵螺塞。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。