查询词典 scheme out
- 与 scheme out 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
The selection of the data transmission scheme is carried out during an active communication link between the first and a second transceiver unit.
在第一和第二收发器单元之间的活动通信链路期间执行对数据发送方案的选择。
-
Both viscous damping and air drag force must be introduced into the dynamic models. The experiment is carried out in the single-axis air-bearing test bed according to the experiment scheme in chapter 3. The results demonstrate the validity of the developed model, while the conventional zero-order approximate approach could lead to bad results for some high speed cases.
结果表明了传统零次近似方法在某些条件下已不能正确描述柔性体的刚柔耦合动力学性质,而一次近似的刚柔耦合动力学模型得到的结果与实验相符,从而证实了一次近似耦合模型的正确性和可靠性。
-
We get the optimum process scheme which is suitable for the unit, through analysising and comparising different absorption schemes in the incipience of running of PSA. As to different operation conditions during pressure swing absorption actual operating, we propose to refer absorption cycle time, hydrogen yield and recovery rate as target of process characteristic, study and find out the interrelation between process parameters which influences each other and controls guideline; Through optimizing process conditions, we find out the best operation clicking in actual production, then confirm the best range of absorption cycle time, which make hydrogen yield of plant, hydrogen products purity and hydrogen recovery rate come up to the production requirement at the same time.
通过装置运行初期对不同吸附方案的分析、比较,选出适合本套装置的最优方案,针对变压吸附实际运行过程中的不同生产条件,提出了吸附时间、氢气产量和氢气回收率作为工艺条件研究的主要对象,找出相互影响的工艺参数和控制指标的相互关系;通过对工艺条件的优化,找出实际生产中最佳操作点,确定吸附时间的最佳范围,使装置氢气产量、氢产品纯度和氢气回收率同时满足生产要求,并对影响氢气回收率的其他因素进行了阐述,对优化操作提出建议。
-
Whose content is pursued including using the AutoCAD software to draw out a part , is pursue the parametric choice carrying out analysis , blank choice , electricity to the part, the machine tool choice workpiece dress gripping and rectifying CAXA line cutting programming , the part treating and so on, reaches the scheme knowing well that a part processes process from blank to finished product's, and processes the problem should pay attention to in process and solving thereby
本次毕业设计的内容是电火花线切割样件加工,主要是对零件凹角和尖角进行电火花线切割加工,其内容包括使用AutoCAD软件绘制出零件图、对零件图进行分析、毛坯的选择、电参数的选择、电极丝的选择、机床的选择、工件的选择、工件的安装及校正、CAXA线切割编程、零件的加工等,从而达到熟悉一个零件从毛坯到成品的加工过程,以及在加工过程中应注意的问题及解决方案。
-
Whose content is pursuedincluding using the AutoCAD software to draw out a part , is pursuethe parametric choice carrying out analysis , blank choice ,electricity to the part, the machine tool choice workpiece dressgripping and rectifying CAXA line cutting programming , the parttreating and so on, reaches the scheme knowing well that a partprocesses process from blank to finished product's, and processesthe problem should pay attention to in process and solvingthereby
摘要本次毕业设计的内容是电火花线切割样件加工,主要是对零件凹角和尖角进行电火花线切割加工,其内容包括使用AutoCAD软件绘制出零件图、对零件图进行分析、毛坯的选择、电参数的选择、电极丝的选择、机床的选择、工件的选择、工件的安装及校正、CAXA线切割编程、零件的加工等,从而达到熟悉一个零件从毛坯到成品的加工过程,以及在加工过程中应注意的问题及解决方案。
-
In this thesis, I summarize the theoretical calculation method, applied scope and notice of siphonic drainage system, and point out the advantage of siphonic drainage system compared with gravitation drainage system. In the archetype experiment study of siphonic drainage tube, I adopt different tube diameter and different structural height to survey the drainage volume and press in different place. I observe various kinds of flow state, and get chief factors which influence hydraulic peculiarity of system as the tube diameter or structural height, and find out the relevance of factor to flux. I apply CFD Fluent software and adopt standard k-ε model and RNG k-ε model, then use finite volume method and second-order upwind scheme to discrete numerical model, while coupling numeration of velocity field and press is based on SIMPLE. In the numerical simulation of curved part of tube, siphonic drainage tube experiment system and multi-outlet siphonic drainage system, I make research on internal velocity and press of system in different project condition by changing the tube diameter of curved part, negative press value in tube export and improving the quantity of water gutter. This thesis first adopts a method of combining archetype experiment and numerical simulation to study the siphonic drainage system, test and verify the validity of experiment and numerical simulation, and makefurther study on system, it solves the problems of limited testing conditions, and has a logical results, it can provide a valid method for optimizing and designing the drainage tube-net system. The conclusion have referring value for study and design of siphonic drainage system.
本文首先对虹吸式排水系统理论计算方法、适用范围以及注意事项做出总结,并分析了虹吸式排水系统的优势;再对虹吸式排水管道进行原型试验研究,采用不同管径不同立管高度,对系统流量、管道压强进行量测,观察了各种工况下的流态,对其水力特性进行研究分析,找出影响水力特性的落差、管径主要因素以及与排水量的关系;进一步应用计算流体力学Fluent软件,采用标准κ-ε模型与RNGκ-ε模型,计算过程应用有限体积法和二阶迎风格式对数值模型进行离散,速度和压力的耦合采用SIMPLE算法,分别对系统弯管段、虹吸排水管道试验系统、多斗虹吸式排水系统进行数值模拟分析,通过改变管段弯头处半径、管段出口负压值、增加雨水斗数对不同工况下系统内部的速度和压力进行研究;本文首次采用结合原型试验与数值模拟相结合的方法,对虹吸式屋面雨水排水系统进行研究,试验与模拟相互验证,并进行拓展,很好地解决了虹吸式屋面雨水排水系统由于试验条件限制问题,结果正确合理,为排水管网系统设计和优化研究提供了有效的方法,对工程设计有较好的参考价值。
-
This essay gives an introduction to the recondition scheme of cambered axle equipped with big-diameter gear wheel, and determines the in and out pressure existing when cambered axle is equipped with gear wheel, as well as its out-pressure project which serves as a solution to the unsettled problem in the course of cambered axle recondition.
介绍装配大直径齿轮曲轴的修复方案,确定曲轴与齿轮装配时压入力、压出力以及压出方案,解决曲轴修复过程中加工设备难已满足的问题,为冶金行业曲轴的修复利用开辟了一条新的途径
-
This thesis mainly includes the following aspects: systematical introduction to environmental protection textile and garment products consciousness and opinions as well asstandards, and introduction and analysis of main environmental protection textile and garment products in the world at present; experiments on testing the wearing properties such as appearing shape, wet comfort, and wear-resistance and so on ,of various Tencel, Modal and cotton knitted fabrics and then analyzing and evaluating these wearing properties so as to get all factors influencing their wearing properties through contrasting different fabrics; by clustering analysis processing and analyzing data from experiments ,in order to evaluate wearing properties of Tencel and Modal fabrics and gain further conclusions; working out a detailed practical scheme for S company to develop environmental protection knitted garment products , analyzing the necessity and feasibility to develop such products, purling forward schemes in developing products and carrying out brand strategy and estimating their economic benefits.
为此,本文主要进行了以下工作:系统阐述了环保纺织服装产品的理念、标准并对目前国内外主要环保纺织服装产品进行评述和分析;实验测试不同种类的天丝、莫代尔和棉等针织物的外观形态、舒适性、耐用性等三方面的服用性能,对天丝和莫代尔针织织物的各项服用性能进行分析评价,并从不同织物性能差异的分析比较中得出影响该类织物服用性能的各项指标;采用数理统计中的聚类分析方法对实验测定的织物各项服用性能的数据结果进行处理和分析,将各项测试结果综合考虑,以评价天丝莫代尔织物的综合服用性能;对国内著名服装企业S公司开发该类环保面料的针织服装产品具体实施方案进行了研究,分析企业开发该类新型服装产品的必要性和可行性,初步设计提出了企业产品开发和品牌操作方案并对该方案的经济效益进行了预测分析。
-
This design passes to turn round the kiln industrial art to steer the research to the cement, establishing the control scheme of the system, this design is mainly to carried out the side to commit some research analyses to the revolving speed of the coal feeder in the hardware, making use of the single machine of sheet of MCS-51 to carry out the revolving speed control of the cement turn-over kiln coal feeder.
0求助!中译英请高手指点,将下面文字翻译成英文,谢谢!本设计通过对水泥回转窑工艺进行研究,确立了系统的控制方案,本设计主要对喂煤机的转速在硬件实现方面做了一些研究分析,利用MCS-51单片机实现水泥回转窑喂煤机的转速控制。
-
The sightline control strategy for bad measure precision is developed, and the control methods for vertical direction, approach direction and station keeping are presented.(2)The safe approach velocities are investigated for cuboid, sphere and cone keep out zone.(3)The design method for optimal trajectory under safety constraint is developed. The cone and cuboid keep out zone can be described using line constraint, and then optimal trajectory design can be translated to line programming problem under line constraint.(4) The design strategy of collision avoidance maneuver is discussed, and the collision avoidance scheme is analyzed for V-bar and R-bar approach.The control and trajectory safety in departure phase are investigated.
1提出了测量误差较大时平移靠拢段的视线控制策略,给出了横向、纵向和悬停的控制方法;(2)针对长方体禁区、球形禁区和锥形禁区三种禁区形式,研究了V-bar逼近和任意方向逼近的纵向安全速度计算问题;(3)提出了安全约束下的最优轨迹设计方法,将冲量和有限推力作用下的最优轨迹设计问题转化为线性规划问题,并给出了将锥形和方形安全区域约束转化为标准线性约束的公式;(4)探讨了紧急避撞机动的设计策略,分析了V-bar和R-bar接近的紧急避撞机动方案。
- 推荐网络例句
-
With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.
随着死亡的吉他手Schuldiner接受主唱的职务,乐队在现实中树立了重要的影响。
-
But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.
不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐,因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。
-
Closes the eye, the deep breathing, all no longer are the dreams as if......
关闭眼睛,深呼吸,一切不再是梦想,犹如。。。。。。