查询词典 scanning speed

Combined with such characteristic parameters as chubbiness, fullness and intensity factor, etc., this process can automatically and adaptively choose the proper scanning pattern, moving speed of the platform and diving depth in according to the shape features of each layer and structural features. The process greatly enhances the prototype's building efficiency and consequently reduces the operation cost of RP machine.

为了能够在保证精度的前提下尽可能提高原型的制作效率，本文提出了自适应智能制作工艺流程的概念，结合饱满度、充盈度、强度因子等特征参数，该工艺能够根据层截面的形状特征及已原型固化部分的结构和强度，自适应地选择适当的扫描方式和托板的升降速度、下潜深度，极大地提高了原型的制作效率，从而有效地降低了成型机的运行成本。

One slightly concave cylindrical lens combination is used to change one laser beam into small sector in small angle, and one reflector projects the laser beam to prism driven by a motor to rotate in high speed to produce one reciprocating and scanning small sector plane.

采用微凹柱面透镜组将激光光源发射的一束激光拉成具有微小夹角的小扇面，利用反射镜将此激光束透射到由电机驱动的高速旋转多面棱体上，使激光束产生一个小扇形往复激光扫描光平面。

This model is JFL-50B aircraft upgrades, the use of international advanced YAG laser technology and micro-computer control technology, high-speed scanning galvanometer, marking high precision, speed and stable performance, is a mature technology products, with good performance and low cost.

本机型是JFL-50B机型的升级版，采用国际上先进的YAG激光技术及微型计算机控制技术，高速扫描振镜，标刻精度高、速度快、性能稳定，是一种技术成熟的产品，具有良好性能价格比。

The heat generation curves of seven rubber materials used in tires with the changes of temperature have been obtained by using Dynamic Mechanics Analysis technique on NETZSCH DMA242 instrument, knowing that the heat generation of every other rubber materials except inner liner rubber changes lightly alone with the temperature within 10℃～80℃. According to the Fourier law, the heat transfer coefficients of tire rubber are measured by stable method on self-made experiment instrument. The coefficients changes lineally within 20℃～80℃ and the relation formulas λ=λ〓+bt are given out attached with λ〓 and b. The specific heat of tire rubber are measured on Differential Scanning Calorimeter NETZSCH DSC204 and the relations with temperature are linear and the formula is c=c〓+bT, where c〓 and b gained from experiment result data are presented in the paper. The heat convection coefficients on the surface of rolling tire are measured according to the principle of heat-mass transfer analogy principle after simplifying rolling tire into rotating disk with straight movement on wind channel. The relation with rotation speed of disk is linear as h=5. 399+0.0258n and the relation with straight line speed of tire is linear too, h=

论文采用动态力学分析技术，使用NETZSCH DMA 242型实验仪，获得了轮胎用七种胶料的生热率随温度变化曲线，确知除内衬层胶以外，其它各种胶料在一般胎温范围内（10℃～80℃）的生热率随温度变化不大；轮胎胶料的导热系数根据傅立叶定律的基本原理，采用稳态法在自行搭建的实验台上进行测试，结果表明，材料的导热系数在20℃～80℃的温度范围内随温度呈线性变化，论文给出了各种材料导热系数的线性变化的关系式λ=λ〓+bt及其λ〓和b的值；轮胎胶料的比热运用差式扫描量热原理，在NETZSCH DSC204型DSC实验仪上进行测试，结果表明，胶料的比热随温度的变化呈线性变化，其关系可用c=c〓+bT表示，文中给出了根据实验数据拟合的c〓、b的值；对轮胎表面的对流换热系数的测定，本文先将滚动的轮胎简化为有直线运动的旋转圆盘，而后采用萘升华热质比拟技术，在风洞中测量了滚动轮胎表面的对流换热系数，结果表明，圆盘表面对流换热系数与转速呈线性关系，即h=5.399+0.0258n，轮胎表面对流换热系数与其直线运动的速度呈线性关系，即h=

Product features: 1, automatic satellite system power automatically begin searching and tracking satellites; 2, Express to capture the use of WRS algorithm for finding stars at Express looking for about 15 seconds to track satellites; 3, receive real-time tracking of satellite signals, high-speed DVB identification code in order to achieve continuous flow of radio and television programs to watch; 4, automatic identification in the frequency and be able to accurately identify the location on the target satellite; 5, scanning electron velocity EBF sweep mode to ensure that the system 100 times per second tracking sweep speed, so that the antenna system to ensure that the system at all under any uninterrupted for watching satellite television programs and allowing the system to greatly increase the service life; 6, self-diagnosis can be their own fault diagnostic equipment, including communication links, sensors, drives, etc..

产品功能：1，自动寻星系统通电后自动开始搜索跟踪卫星；2，快速捕捉利用WRS寻星算法在15 秒左右快速寻找到跟踪卫星；3，接收信号实时跟踪卫星，高速识别DVB 码流以实现连续收看广播电视节目；4，自动识别能够在频率和位置上准确的辨别目标卫星；5，电子波速扫描 EBF扫模式保证了系统每秒100次的跟踪扫速度，使天线系统保证系统在任何条下都能不间断的收看卫星电视节目且使系统的使用寿命大大增加；6，自我诊断可以自行诊断设备故障，包括通信链路、传感器、驱动装置等。

The microstructure of Ti Zr alloy formed under this suitable technologic parameter matching was analyzed by scanning electron microscope. RESULTS: When the ratio of laser power to facular diameter was 2.7 kW/3 mm, the powder feeding speed was 90 r/min and the moving speed of numerical control machine was 5 mm/s, better H (826.61 μm) and W (3504.61 μm) were obtained.

结果： 在激光功率与光斑直径之比为2.7 kW/3 mm，送粉器转速为90 r/min和数控机床的运动速度为5 mm/s等参数下，Ti Zr粉末激光立体成形时具有较好的H和W，分别为826.61 μm和3504.61 μm。

No entire nitrendipine crystals were observed visually in SEM photos. The results of X-ray diffraction and differential scanning calorimetry analysis indicated that the crystalline form of nitrendipine was highly dispersed in microspheres, so as amorphous state. The drug release rate of microspheres could be controlled with adjusting the ratio of solid dispersion carriers and retarding agents formulated. The agitation speed and temperature of the preparation process have distinct effect on micromeritic properties of microspheres. The release profiles of the microspheres were mainly affected by the stirring rate of paddle, the concentration of SDS and pH of dissolution medium. Cooling speed and time, however, have no evident influence on the drug release rate of the microspheres. The dissolution data showed that the mechanism of drug release from microsphers was mainly diffusion-controlled. The incorporation efficiencies of 3 batches sample were exceed 96. 8％, which implied that the current method was suitable for design sustained-release dosage form for poorly water-soluble drug.

在扫描电子显微镜下观察，在微球内外未发现尼群地平的完整结晶，X-射线粉末衍射和差示扫描量热试验结果也显示，尼群地平已经被高度分散在微球中；微球的释药速度可通过调整处方中固体分散体载体和阻滞剂的比例控制；制备温度和搅拌速度对微球的质量影响较大；溶出仪的搅拌速度，释放介质的浓度和pH对微球的释放有较大的影响；制备过程中的冷却速度和冷却时间对微球的释放行为影响不很明显；方程拟合的结果表明缓释微球的释药行为符合扩散机制；测定三批微球样品的包封率均在96.8％以上，表明该法适合于制备难溶性药物的缓释微球。

This device include: Renishaw's high-speed scanner (CYCLON SERIES2), the scanner can be laser-contact probe and probe each other's advantages, precision laser scanning for 0.05mm, contact scanning probe accuracy Up to 0.02mm.

这方面的设备还包括：英国雷尼绍公司的高速扫描仪（CYCLON SERIES2），该扫描仪可实现激光测头和接触式测头优势互补，激光扫描精度为0.05mm，接触式测头扫描精度达0.02mm。

The effect of the tool composition on the friction and wear behavior was investigated,and the morphologies of the rake face and rear face of the tool cutting the steel in air and nitrogen were observed on a scanning electron microscope. It was found that the Al_2O_3/TiB_2 tool was dominated by adhesive and abrasive wear in low speed dry cutting; while in high speed dry cutting,the tool was characterized by oxidation wear. An oxide layer of TiO_2 was formed by way of the oxidation of the reinforcing agent TiB_2 at a very much high cutting temperature, which contributed to greatly reducing the friction coefficient and increasing the antiwear life of the tool.Such a friction-reducing and antiwear behavior of the oxide layer was enhanced with increasing content of TiB_2 in the tool composite. However,the tool showed a relatively poorer wear resistance in N_2 than in air, because N_2 acted to retard the oxidation of the TiB_2 and the formation of the oxide layer on the tool rake face.

结果表明：低速干切削时，Al2O3/TiB2陶瓷刀具的磨损机制主要表现为粘着磨损和磨料磨损；而在高速干切削时，刀具的磨损机制主要表现为氧化磨损，刀具表面经由氧化反应生成具有润滑作用的反应膜而起到固体润滑作用，从而使刀具的耐磨性能提高，随着TiB2含量和切削速度的增加，反应膜的减摩抗磨作用增强；而在切削区通入氮气时，由于刀具表面氧化膜形成受阻，刀具的抗磨能力有所降低。

The key techniques of STM IPC-205B were shown as following: the design of the micro-displacement transmission system with wide scope and high speed; the physical mechanism and vibration-proof measures which greatly influence the theoretical precision of STM; the basic design theory of scanning system and data collection system; the methods of the intelligent control of scanning voltage and the logarithm contraction of tunnel current.

对STM IPC-205B型机关键技术进行了探讨，主要包括：大范围快速扫描的微位移传动系统的设计；对实现STM理论精度有重大影响的振动源的物理机理以及防振的措施；扫描与数据采集系统设计的基本理论；给出了实现扫描电压的智能控制和对隧道电流进行对数压缩的方法。

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。