查询词典 scanning speed
- 与 scanning speed 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Moreover,if the laser scanning speed istoo faster,the organic matter within the coatings may not elininate fully during the laserirradiation period.When the molten pool begin to solidify,the trapped residual organicmatter may burn,carbonize and boil within the cooling pool,which results in trappedbubble defects inside on the surface of the sintered electronic paste film.
由于扫描速度过快,残留有机物在熔池存在时间内不能完全烧蚀气化,在熔池开始冷却凝固时将可能发生有机物蒸气波沸腾-爆破现象,导致浆料膜层内部气泡和表面爆破孔洞缺陷。
-
The process of dip pen lithography involves the adsorption of ink molecules on AFM tip ,the formation of water meniscus ,the transport of ink molecules ,and diffusion of ink molecules on the substrate .More factors such as temperature ,humidity ,tip ,scanning speed and so on will influence the process of dip pen lithography .
蘸水笔技术的刻蚀过程包括AFM 针尖对墨水分子的吸附、针尖与基底间弯月液桥的形成、墨水分子在液桥中的传输、墨水分子在基底的扩散等四个阶段,并受温度、湿度、针尖、扫描速度等多种因素的影响。
-
The result shows that the power density and scanning speed are two important factors to produce glassy surface layers.
试验结果表明,激光功率密度和激光扫描速度是实现材料表面非晶化的重要条件。
-
Results When scanning speed of frequency-tripled Nd : YAG laser was no more than 80 mm/s, the thermal damage rate was lower, and the aperture size of microperes varied indistinctively.
结果激光束扫描速度小于或等于80mm/s,热损伤率较低,微孔孔径变化不明显;随着激光束扫描速度的加快,热损伤率增大,孔径随之增大;当扫描速度加快至500mm/s,孔径开始缩小;当扫描速度为600mm/s,激光束不能穿透真皮基质形成微孔。
-
As a result, the achieved uncertainty of time measuring is±125 ps, demonstrating an accuracy improvement in magnitude of an order. The achieved precision of speed measuring is 0.1% of the scanning speed. In hardware design, the intactness of the camera's original structure has been maintained to the very extent, the facility of assembling and disassembling devices have been achieved.
在设计制作中采用了单色性和方向性好的激光作为光源,选取了高速响应和有高速处理能力的一系列器件、芯片,因此时间测量的精度达到了±125 ps,比以往的测试方法提高了1个数量级以上,速度测量精度达到扫描速度的0.1%。
-
Thus, the spherical-crown and saddle-shaped surfaces were demonstrated. Consequently, the basic rules and key technology of bending forming using plasma arc in practical work were obtained and the application level of the flexible forming using plasma arc had been further improved. The effects of the main parameters including power, scanning speed, scanning distance and scanning sequence had been investigated.
对成形中出现的棱角效应进行了机理分析和数值计算,结果表明棱角效应是板材沿扫描线方向受几何约束产生了较小的压应变及在扫描线上、下表面的收缩量不同所造成;提出了通过分段扫描解决棱角效应的方法,明显提高了成形质量。
-
There are to be used in laser ultrared, green, purple, and so on a number of speed to violet laser, the fastest scanning speed up to 5 50 line/min, equivalent to 1 minute 46 seconds to 2,400 dp I completed a 1,024 x 800 mm (28 "x 40") caoju full page exposure.
而搁置的雷射有红外线、红、紫色等数栽,其速率给算紫雷射最快,扫描速率能矮达5 5,000线/不合,不等于1不合46秒边能以2,400 dp i达不败一弛1,024 x 800 mm(28" x 40 ")菊残版的曝平。
-
The laser-cladding layeron the alloy consists of matrix phase of over-saturation solid solution γ and complexhexagonal carbide M_7C_3. Under certain condition, with fast laser scanning speed, the oversaturation solubility of elements increases in γ, and the precipitation of the complexcarbide M_7C_3 decreases, so that the microhardness increases and the wear resistance de-creases. But at slower laser scanning speed, more complex carbide M_7C_3 may precipitate, andthe wear resistance may be improved. Therefore, it is believed that the principal factor in im-provement over wear resistance is the precipitation of carbide M_7C_3, while overmicrohardness is the over-saturation solubility of elements in matrix phase.
表明:(1)激光熔覆合金层是由过饱和的γ基体相和复杂的六方M_7C_3碳化物相所组成(2)在其他参数不变的情况下,随激光扫描速度的提高,γ基体相过饱和度增大,而析出的碳化物含量减少,因而合金层的硬度升高,耐磨性有所下降;而降低激光的扫描速度,碳化物M_7C_3析出增加,有利于提高合金层的耐磨性、因此碳化物M_7C_3析出量是提高耐磨性的主要因素,而增加基体相γ的过饱和度则是硬度提高的主要因素
-
For the balling of scanning line, the process parameters with the ratio of power to scanning speed greater than 0.10 are employed to form a continuous scanning line.
对于扫描线的球化,采用功率与扫描速度的比值大于0.1的工艺参数进行扫描,获得了连续的扫描线。
-
The mathematical model by which the forming time can be precisely calculated is ratiocinated. This model shows that in SLS the scanning "delay" phenomenon can make the actual forming time greatly exceed the theoretical time, and the total number, total length of the scanning lines and the scanning speed have different effects on the scanning "delay".
本文推导出了SLS成型时间精确计算的数学模型,该模型显示在SLS加工中的扫描&延时&现象会造成实际成型时间远远大于理论时间,并且扫描线条数、扫描线总长和扫描速度对扫描&延时&有不同程度的影响。
- 推荐网络例句
-
I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""
客人们在卡罗利娜·埃凯家里,举止就文雅一些,因为卡罗利娜的母亲治家很严厉。
-
Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.
由著名品牌 Herm è s 设计,这件高贵的制服是香港本土制造,是我们第一套不配帽子的制服。
-
Do not 'inflate' your achievements and/or qualifications or skills .
不要 '夸大' 你的业绩或成果,条件或者技能。