查询词典 scale modulus

The digital simulation of thedynamic processes under step load input and supply oil pressure fluctuation were carried on by MATLAB. Analysis of the dynamic characteristics was done with the changes of the supply pressure, load, structural parameters of spherical hydrostatic bearing and the effective bulk modulus of oil. The conclusions show that structural parameters of the spherical bearing and the effect bulk modulus of oil have significant influence to dynamic characteristics, but the elasticity deformation of interior supporting collet has very small influences on the output response characteristics of the suspension system. The collets deformation can be neglected on the project.

在此基础上，建立了考虑内支撑筒的弹性变形与否时悬浮系统的数学模型，同时，建立了线性化的仿真模型，利用MATLAB对阶跃负载输入和油源压力脉动输入下的系统进行动态过程的数值仿真，结果表明球面副的结构参数，油液的有效体积弹性模数对系统的响应特性有明显的影响，而内支撑筒的弹性变形对悬浮系统的响应特性的影响很小，在工程上可以忽略其弹性变形。

The Hilbert modulus is defined as the sum of the square of a signal and its conjugation.Hilbert modulus is used to covert the fundamental component in original phase current to direct current component,the fault characteristics frequency of bar break is transformed into the twice slip frequency.The problem is solved that fault characteristic component in the spectrum analysis of the current is easily to be blanketed by fundamental component and is hard to highlight fault characteristics.

将Hilbert模量定义为原始信号与其共轭信号的平方和，利用Hilbert模量将原相电流中的基波分量转变为直流分量，原频谱分析的转绕组断条的故障特征分量转变为频率为二倍转差频率的电流分量，决了相电流频谱分析方法中断条故障特征成分容易被基波湮没而难以突出故障特征的问题。

At the phase inversion point,the viscosity of the system at low stress increases slightly and the dynamic rheological parameters (storage modulus,loss modulus and complex viscosity) reach their minimum values.

摘 要 以动态应力流变仪DSR对双酚A型环氧树脂在低乳化剂浓度(2.33wt%)下的相反转乳化过程进行了稳态应力扫描及动态频率扫描实验。

The company worked for research and development of motorcycle gear and automobile gear, and become a lead in manufacture mid modulus gear and small modulus gear.

自公司建立以来就致力于各型摩托车齿轮和汽车齿轮的研发与制造，并逐渐成长为中小模数齿轮生产厂家的领先企业。

The storage modulus is increased with the increase of Cf, while the peak temperature of loss factor and the temperature of loss modulus are not changed with the variation of Cf, which means that the reinforcement of chitin fiber has no effect on the motion of molecular segment for PCL.

动态热机械分析表明，复合材料的储能模量随纤维含量的增加而增加，表征玻璃化转变温度的损耗因子松弛峰的峰值温度和损耗模量的温度都不随纤维含量的改变而变化。

The results showed when the coated PVC fabric scraps were palletized by means of extrusion directly, the strength of the moulded part was weaker than that of the part made from PVC monomer. After the compounding of the fabric scraps with nonwoven PP fabric scraps and waste PE fishnet, the strength and elastic modulus of the composite increased obviously, the toughening effect of the glass fiber was especially noticeable in the form of tensile modulus.

实验结果表明：利用纤维类下脚直接挤出造粒工艺，其注塑成型品的强度要低于PVC单体的强度；通过与PP和PE复合后，复合材料的强度和弹性模量得到显著提高，特别是弹性模量方面显示出了玻璃纤维的增强效果。

The process method of kaolin was introduced using A-151 and ester titanate coupling agent. Effect of dosage of A-151 and ester titanate coupling agent on stretch strength and modulus, bending strength and modulus , impact strength of UPR was investigated.

介绍了用A - 15 1与钛酸酯偶联剂处理高岭土的方法，研究了处理剂的用量与偶联高岭土的加入量对UPR的拉伸强度和模量、弯曲强度和模量以及冲击强度的影响。

When the elastic modulus is high, stress and strain are mainly concentrated at edge of the overlap region, while those in weld spot zone are relatively even; when the elastic modulus is low, stresses in the adhesive layer are small while stresses are concentrated to a certain extent at edge of the weld spot.

分析发现，胶粘剂弹性模量对接头中应力应变分布的趋势有明显影响，胶粘剂弹性模量高时，搭接区边缘附近区域应力应变高，焊点区应力应变值相对较小；弹性模量低时，焊点边缘处存在一定的应力集中，胶层中应力较小。

Results show that when improving spot pitch in weld bonded joints with high elastic modulus adhesives, stresses in weld spot zone are decreased while stresses and strains at edges of overlap region are increased slightly. For the joints with low elastic modulus adhesives, both stress concentration degree at the weld spot and the shear strain at edges of overlap region are increased with the spot pitch increasing.

结果表明，高弹性模量胶粘剂胶焊接头中，增大焊点间距，焊点区应力减小而搭接区边缘胶层中的应力应变略有增大；低弹性模量胶粘剂胶焊接头中，焊点处应力集中程度和搭接区边缘胶层中的剪应变值都随焊点间距的增加而增大，增加焊点间距，两种接头的胶层断裂强度都将降低。

With analysing the the fatigue mechanism, the general mode of interply fatigue damage propagation is denoted by delamination length and crack density. Based on the power-law, the relationship between number of cycles and delamination length and crack density are established. The specimen is modeled as an equivalent six-ply material system. Starting with the analysis of interply stress, the interply shear stress under cyclic loading is calculated by using nonlinear three-demension FEA. According to the stage regularity of fatigue damage propagation, such models as average strain, effective modulus, ratio of delamination length and crack density, experimental relationship between crack density and effective modulus, are proposed by introducing subsection coefficient.

通过对疲劳机理的分析，确定了以脱层长度和裂纹密度表示的层间疲劳损伤演化的一般模式，利用指数法则建立了脱层长度和裂纹密度随疲劳循环周次变化的关系；从层间应力分析入手，以等效六层的材料模型对循环载荷下的层间剪切应力进行了三维非线性有限元分析；根据疲劳损伤扩展的阶段性，引入分段系数，分别建立了平均应变与载荷循环周次的分段线性模拟模型、有效刚度随载荷循环周次的变化关系模型、裂纹密度变化和脱层长度变化关系随载荷循环周次变化的分段线性模型以及疲劳裂纹密度和有效刚度关系的经验模型。

Vishnu entered a dark fourth dimensional dream that did not support his field or continued life.

毗瑟挐进入了一个第四密度的黑暗梦想，那里并不支持他的能量场或继续生命。

Leaders and decision-making persons use it to collect the data, including the information of unit work, handing in fee, oweing fee, prepaying fee,changing and afterpaying and account transfering of joining-insurance employee, and account paying of all kinds of insurances from hospitalization insurance institutions.The collected data is picked up, organized, switched and showed to user.

该子系统主要面向各级领导、决策分析人员；从各个医疗保险经办机构和定点医疗机构采集数据，包括在各个医疗保险经办机构处理的单位办公信息，单位缴费、欠费、预缴费信息，参保职工变更信息，参保职工增减变动信息，参保职工补缴信息，参保职工帐户划拨信息：包括各定点医疗机构处理的各险种帐户支出信息，各险种的统筹金支付信息等；将采集的数据提取，组织和转换，然后展示给用户。