查询词典 sampling

This thesis contributes to geometry compression in the following aspects: Proposes a method of progressive spherical mesh parameterization based on local parameterization by directly projecting the deleted vertices to its neighborhood. Based on spherical mesh paramterization, an adaptive subdivision remeshing method by progressivly redistributing of sampling points is proposed, by this means, the main geometry information of the original mesh can be captured with only a small amount of samples, it can also be used in mesh simplification. By regarding attributes binded on mesh vertices as geometry signals and transferring them onto a uint sphere by means of spherical mesh parameterization, meshes with different attributes are compressed with spherical wavelet successfully with high compression rate. As a kind of lossy geometry compression technique, two mesh simplification algorthimes are also presented in this thesis.

归纳起来，本文的主要贡献有：提出了以直接投影局部参数化方法为基础的网格累进球面参数化方法；在网格球面参数化方法的基础之上，提出了一种基于累进优化布点方案的网格细分采样方法，该方法可以用很少的采样点就可以捕获到网格的主要特征，因此我们也将其用于后面的网格简化工作当中；通过将网格顶点上定义的各种属性看成几何信号，并以网格球面参数化为手段将几何信号迁移到单位球面上，从而成功地实现了用球面小波对各种几何信号的压缩；作为一种有损压缩方法，本文还提出了基于统一距离的网格简化算法和基于重采样的网格简化算法。

Firstly, we use Gaussian kernel function to replace the Dirac delta kernel function, and embed the re-sampling into filtering to eliminate the impoverishment problem of the standard particle filter.

2为了解决光线变化的情况下，以及发生旋转、平移和尺度变化等姿态变化的运动目标的鲁棒跟踪问题，提出了一种基于自适应观测模型的粒子滤波跟踪算法。

The effects of data sampling methods, its density and distribution on the accuracy of DEM are presented.

阐述了原始数据的采集方法及其密度、分布对 DEM 精度的影响。

The digital processing front aims to demodulate I/Q signal and transform sampling frequency.

在数位处理前端的部份是将取样出来的讯号做I/Q讯号的解调变和取样频率的转换。

This design uses the monolithic integrated circuit to control 8 groups signals the sampling as well as the read-write process, uses the monolithic integrated circuit stored datum, uses the monolithic integrated circuit AT89S52 readout, through application software, 8 group signal demonstrations on hypothesized , and uses the light emitter diode demonstration.

本设计采用单片机控制8路信号的采样以及读写过程，采用单片机存储数据，采用单片机AT89S52读出数据，通过应用软件，将8路信号显示在虚拟示波器上，并且用发光二极管显示。

This design uses the monolithic integrated circuit to control 8 groups signals the sampling as well as the read-write process, uses the monolithic integrated circuit stored datum, uses the monolithic integrated circuit AT89S52 readout, through application software, 8 group signal demonstrations on hypothesized oscilloscope, and uses the light emitter diode demonstration.

本设计采用单片机控制8路信号的采样以及读写过程，采用单片机存储数据，采用单片机AT89S52读出数据，通过应用软件，将8路信号显示在虚拟示波器上，并且用发光二极管显示。

After roller compaction,the wet density of RCC would be measured by sampling from the digged pit or by nuclear densimeter.

碾压后，挖坑取样或采用核子密度水分计选点测量碾压混凝土的湿密度。

2 Hole size: densitometer structure, used to restrict the optical throughput and size of the sampling area..

3.2光孔大小：密度计结构中，用来限制光的通过量和采样面积的大小。

The improved method of filter sampling off-line analysis using both parallel plate organic denuder and backup filter has a good agreement with in-situ online measurement.

同时采用平行板有机物扩散吸收管和后置膜的离线分析方法同在线观测的结果具有比较好的一致性。

The purpose of this study was to measure the gaseous inorganic acids / bases and volatile organic compounds emitted during the business of central Taiwan Science Park, and establish the air quality data. Two sampling sites were located in the north and south of the Park. The measuring instrument was the annular denuder system for inorganic acids and bases and the method for VOCs' measurement was according to Taiwan's EPA method NIEA

中文摘要本研究之目的乃在建立中部科学园区之空气品质污染物浓度资料，监测地点为基地北侧的土地公庙及南侧的国安国小，监测污染物包括空气中气状、粒状的无机酸碱及挥发性有机化合物等气体，监测仪器及方法依据则分别为环型扩散采样器及环保署环境检验所公告之NIEA A715.12B方法。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐