查询词典 rupture load

In quantitatively analysis including process of loading and stress distribution along the body of a chimney, load of blasting vibration induced by the forming of blasting cut was analyzed and the premature rupture of upper chimney was certainly affected by it.

将ANSYS5.7瞬态动力学分析引入爆破动力计算中，定量分析研究了在切口形成时的爆破振动荷载下，整体结构受力过程及应力分布规律。

The ultimate torsional strength or modulus of rupture expresses a measure of the ability of material to withstand a twisting load.

断裂时的扭转极限强度或模量描述的是材料受到扭曲载荷时的抗扭能力。

Incurrent research, aiming at the rupture problem engendered in the shooting process of acertain 5.56mm automatic rifle, the strain and stress distributions on the cartridge caseunder the action of axial pull have been analyzed. Based on the theories of elastic-plasticmechanics and contact mechanics, a mathematic and physical model of the cartridge-caseand chamber system has been set up; and based on the platform of the general softwarepackage APDL of ANSYS for finite element analysis, a parameterized model of thecartridge-case and chamber system has also been established. The method for nonlinearFEA has been adopted to analyze the stress distribution on the entire cartridge-case andchamber system, and the method of contact element has been employed to investigate thecontact stress between the cartridge case and chamber, and then the influences of frictioncoefficient and locking space on the static and dynamic stress and strain response of thecartridge case and chamber to the action of power gas have also been discussed. On thebasis of a lot of numerical tests, a kind of element Plane13, which is concentrated incoupled computation of heat and construction, has been used finally to simulate thetransient response of the cartridge-case and chamber system to the power gas. Throughloading the temporary thermal characteristics of explosive gas in the procedure of emulate, the corresponding transient thermal stress distributed on the entire system under thecombined load of transient thermal stress and transient pressure has been obtained. Owingto these comprehensive considerations, the numerical results obtained in this paperrepresent the actual situations comparatively exactly.

本文针对某5.56mm自动步枪在工作中出现断壳的问题，分析了弹壳在轴向拉力作用下的应力应变；基于弹塑性力学及接触理论，建立了弹壳弹膛系统的数学、物理学模型，在通用有限元ANSYS软件的参数化建模工具APDL平台上，建立了弹壳弹膛系统的参数化模型；采用非线性有限元法计算了弹壳弹膛系统的整体应力，引入接触单元法分析弹壳和弹膛的接触压力，探讨了在不同的摩擦系数和不同的闭锁间隙对弹壳弹膛静、动态响应的影响；本文进行了大量的尝试，最后确定采用热、结构耦合单元Plane13，在计算中加载了火药气体的温度历程，成功的获得了弹壳弹膛系统在瞬态的热载荷和瞬态的压力载荷同时作用下弹壳弹膛系统的热应力数值解，考虑因素全面，比较真实的反映了弹壳弹膛系统在火药气体压力和热载荷下作用的情况。

Applied overlay principle discloses intention at the complex load of break of grease wall of a well for individual and simple load, through set and time relevant aeriform pressure distributings function, rupture according to flexibility of stretch and mechanical, line condition of tie of stress of the upland after perforation of well of grease of mechanical and academic derivation plays factor of intensity of interstitial and most advanced stress, got deflagrating patulous condition is cracked since terrane of aeriform fracture wall of a well, the aeriform pressure gradient that this condition can follow time change inside reflective break is right the influence of interstitial configuration.

应用叠加原理将功能于油水井壁裂缝的复杂载荷分解为单个简单载荷，通过设定和时间相关的气体压力分布函数，根据弹性力学、线弹性断裂力学理论推导油水井射孔后高地应力约束条件下裂缝尖端应力强度因子，得到了爆燃气体压裂井壁岩层起裂扩展条件，该条件可以反映裂缝内随时间变化的气体压力梯度对裂缝形态的影响。

The supporting frame of cutting platform of back-load-bearing typed corn harvester is a spatial welded structure,it will create an over loading in the front wheel shaft of tractor and cause fatigue rupture of front wheel shaft or cause the tractor to sink into the soil.

背负式玉米收获机割台支架是一个空间焊接结构，在使用中会产生拖拉机前轮轴超重，造成前轮轴疲劳断裂或是拖拉机沉陷土壤中。

Stage 3: When the load was increased beyond P1 (greater than 6000 lb, 26.7KN), tensile stresses in concrete at the tension zone increased until they were greater than the modulus of rupture fc, and cracks developed.

阶段3：当装载在P1 (大于6000磅之外被增加了， 26.7KN)，张应力在混凝土在紧张区域增加了，直到他们大于破裂fc的模数，并且被开发的镇压。

13 Safety valve should also be installed to the steam side of the heater to avoid the excessive pressure caused by the pipe rupture. 10% of peak load water flow should be passed, or the discharge flow of one pipe and two ruptures should be passed. The maximum of the two should be selected and sufficient

5.1.13加热器汽侧也应设置安全阀，防止由于管子破裂而造成超压，其最小容量应能通过最大负荷给水流量的10%或一根管与两个断口排放的流量，两者取最大值并留有足够的安全裕量。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。