查询词典 roughness

It is found that water velocity vertical distribution under ice-cover is influenced mainly by the relative size of channel roughness and ice-cover roughness, less by the water depth and not sensitive to the variation of Reynold number as well, which is relatively uniform in the flow core and deviates from the logarithmic law.

结果表明：冰盖下水流流速垂向分布主要受床面与冰盖粗糙度的相对大小影响，受水深影响较小，对雷诺数变化并不敏感；在流动核心部分分布较为均匀，并不遵循对数分布规律。

Three kinds of cutting material were selected to machine stainless steel machining experiment such as ceramic cutting tools, cermets cutting tools and coated carbide cutting tools, in which the best range of each kind of tool material was founded. For example, LT55 was suitable to be machine lCrl8Ni9Ti as the cutting speed surpasses 120m/min and have a good wearable property.(3) Surface roughness was measured under different cutting conditions. Feed rate played the most important role in impacting surface roughness, and then cutting speed.(4) Chip patterns in different cutting speed with various cutting materials were analyzed. With the increase of turning speed, chip became shorter and was easy to be broken. For instance, serration chip appeared in high sped turning stainless steel with LT55;(5) Work hardening of austenitic stainless steel was analyzed.

陶瓷刀具LT55适合在Vc=120m/min以上切削加工不锈钢，耐磨性好；③通过试验研究了不同刀具材料高速车削加工1Cr18Ni9Ti不锈钢时的表面粗糙度，其中进给量对表面粗糙度的影响最为显著，其次为切削速度；④分析了不同刀具材料在不同切削速度下加工1Cr18Ni9Ti不锈钢的切屑形态，随着车削速度的提高，切屑变短且易断屑，其中LT55陶瓷刀具切削加工时产生了锯齿状切屑；⑤分析了奥氏体不锈钢的加工硬化机理及其对刀具磨损的影响；⑥根据试验结果分析在不同切削条件下切削不锈钢的刀具磨损形式及其磨损机理。

In this paper, the principle and hardware of test system are designed and the step motor's control software is designed at the same time. The assessing methods of linearity errors are analyzed and the test methods of linearity, diameter and roughness are provided and the corresponding softwares are programmed with VB. At last, the test method of roughness without touch-light scattering is proposed.

论文对检测系统的原理及硬件电路进行了设计，同时对步进电机的控制软件进行了详细的设计；对直线度误差的评定方法进行了分析，分别给出了炮膛内径的直线度、直径及阴阳膛表面粗糙度的测量方法，并用VB 编写了相应的控制软件，最后提出了一种炮膛粗糙度非接触测量法—光散射法。

First, the time series model of the random road roughness running by construction machinery is built up based on the measured data of the random road roughness and by means of the basic theory and method of the time series analysis. A real-time parameter estimation method of fuzzy weighted recurrence least square algorithm is represented through analyzing the conventional recurrence least square algorithm. Then, the new recurrence algorithm and the on-line tuning method of the weighted matrix are given out, and computer simulation is performed.

首先，以实测的地面随机不平度数据为依据，应用时序分析的基本理论和方法，建立了工程机械行驶地面随机不平度的时间序列模型，并在分析传统参数估计方法递推最小二乘算法的基础上，提出了模糊加权递推最小二乘算法的参数实时估计方法，给出了在此基础上的递推算法及加权矩阵的实时在线整定方法，并对其进行了计算机仿真研究。

The results show that this kind of roughening elements can possess a wide range of roughness, and the hydraulic resistance decreases with the increase of space between roughness elements, but reduces slowly to a constant, and that flow enters into the turbulently rough zone when Reynolds number reaches about 3 500, in which the hydraulic resistance decreases with increase of relative submergence degree, reducing slowly to a constant too.

通过水槽试验对Y型加糙体阻力特性进行了深入研究。研究结果表明：其糙率具有一个较大的调整范围，且随着加糙间距的增加水力阻力减小，减小的幅度越来越小，最后基本不变；雷诺数在3 500左右水流进入阻力平方区，进入阻力平方区后，随着相对淹没度的增大水力阻力减小，最后达一定值。

According to the request of construction features, processing spot, size precision, surface roughness and productivity that diesel engine air cylinder, sets the machine tool for single location horizontal type modular machine tool. Considered to the factor of the size precision, surface roughness, scrap removes and productivity and so on of the work piece, selects the Hard alloy not grind type surface milling cutter.

根据柴油机气缸体的结构特点、加工部位、尺寸精度、表面粗糙度及生产率等要求，确定该机床为单工位卧式组合机床；考虑工件尺寸精度，表面粗糙度，切屑的排除及生产率等因素，选用硬质合金不重磨式面铣刀；根据工件的尺寸、特点及其材料选择切削用量；然后，再经过切削用量来确定组合机床的通用部件；最后进行组合机床的总体设计。

For different surface roughness of electrodes and glycol concentration of glycol/water mixture, pressurized water breakdown experiments are carried out. Experimental results suggest that Mirza's formula is valid and independent of surface roughness and glycol concentration, and it is accumulative for surface polish, glycol additive, and pressurization for the capability to improve electrical breakdown strength. Moreover, the increase of electrical breakdown strength of water dielectric for surface polish is explained with bubble breakdown. Especially, highest stress of 235.5kV/cm observed in glycol/water mixture with a glycol concentration of 80% at a hydrostatic pressure of 12atm is about one time greater than that in pure water at constant pressure.

通过改变电极表面光滑程度和乙二醇浓度，分别进行了加压水介质击穿实验，证实了不同电极表面光滑程度和乙二醇浓度下Mirza关系式仍成立，抛光电极表面、添加乙二醇与加压在提高水介质电击穿能力方面具有可叠加性，将抛光电极表面、添加乙二醇与加压分别进行了比较，特别，在静压12atm、乙二醇浓度80%下，得到实测最高击穿场强为235.5kV/cm，其有效时间归一化后的击穿场强比常压下纯水的相应值提高了112.2%，运用气泡击穿模型对抛光提高水介质击穿场强进行了物理解释。

Surface roughness and geometry topography have very obvious difference between ordinary and ultraprecision grindings. Surface roughness of ultrapreciscon grinding will decrease with abrasive size and grinding depth decrease, surface veining owing to plastic deformation is very clear.

超精密磨削和普通磨削的表面粗糙度和几何形貌存在明显的差异，超精密磨削的表面粗糙度随着金刚石砂轮磨粒尺寸和磨削深度的减小而减小，表面由于塑性变形形成的纹理比较明显。

In this article, based on an analysis of the geometrical property for waviness and roughness,it is suggested that it is unnecessry to find a parameter of the complete separated component of waviness and roughness.

本文在分析表面波纹度和粗糙度几何特征的基础上，提出没有必要寻求一个截然分离表面波纹度和粗糙度参数的看法。

This article introduces the measuring and the calculation of forward and backward scattering in some range of surface roughness and waviness of laser gyro mirror substrate and presents the effect of surface roughness and waviness on scattering.

研究了激光陀螺反射镜基片表面粗糙度和波度前、后向散射的测量计算及其对散射的影响。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失