查询词典 roughness

The results show that the surface roughness decreases with increase of the inclination angles within the range of 10° to 30°. After the angle approaches to 30°, increase of the inclination angle causes increase of the surface roughness. Furthermore, the effect of inclination angles on cutting speed was investigated.

研究结果表明：工件倾角的大小对已加工表面粗糙度有明显的影响，在倾角为10°～30°时，表面粗糙度随着工件倾角的增大而降低；此后，随着倾角的进一步增加，表面粗糙度有所升高。

Thirdly, Through the introduction of the Burckhardt road model 、Gim tire model、bus brake model and Time-domain model of road roughness ,ABS system with a fuzzy controller based on the slip rate deviation and deviation rate of change was designed. The ABS system on account of impacts of air suspension and road roughness were analyzed, and its result showed that air suspension system and braking system need joint control.

第三，通过引入了描述单轮特性的Burckhardt的路面模型、Gim轮胎模型、客车制动器模型和时域路面不平度模型，并在此基础上设计了基于滑移率偏差和偏差变化率的ABS模糊控制器，对计及空气悬架和路面不平度影响的ABS进行了分析，进而说明了空气悬架系统与制动系统进行联合控制的必要性。

The results indicate that as the value of fractal dimension is increased, the interfacial static friction coefficient first increases and then decreases; the interfacial static friction coefficient decreases as the fractal roughness parameter increases; while the inter-facial static friction coefficient increases as the material property or total normal load increases; the curve of static friction coefficient versus dimensionless total normal load is convex when the fractal dimension becomes smaller or fractal roughness parameter is larger or material property becomes smaller.

研究结果表明：界面的静摩擦因数首先随分形维数的增加而增加，然后随分形维数的增加而减小；界面的静摩擦因数随分形粗糙度参数的增加而减小，但随材料特性的增加而增加，也随总法向载荷的增加而增加；当分形维数较小或分形粗糙度参数较大或材料特性较小时，静摩擦因数－量纲一的总法向载荷曲线为凸弧。

By re-prove the theorem on the relationship between information entropy and roughness of knowledge,this paper finds that it is conditional information entropy which exists one-to-one relationship with roughness of knowledge.Then several related theorems are given and proved.

该文通过重新证明知识粗糙性和信息熵的对应关系定理，找到与知识粗糙性存在一一对应关系的是条件信息熵，并给出相关定理及其证明。

The numerical relationship between the proportionality constant of surface roughness scattering mobility model and surface roughness degree is deduced.

推导出SiC表面粗糙散射迁移率模型的参数与界面粗糙度之间的数值关系。

The value of roughness is depended on landscape, vegetation cover and crop cultivation direction, the larger the roughness is, the less the wind erosion intensity is.

地表粗糙度反映地表对风速减弱的作用以及对风沙流的影响，其值大小取决于地形、植被覆盖及作物的播种方向，粗糙度越大风蚀强度越小。

The main research content is: Using the experimental of cutting force and roughness of high speed face milling cutter and high speed end milling cutter mill aluminium alloy and cast iron, analyze the rules of the high speed milling velocity, feed rate per tooth, milling depth and milling width to high speed processing. Use multiple linear regression method, set up surface roughness and the cutting force fluctuation models. Certify the regression model notability, and provide a reliable guarantee for the accuracy of function optimization. Based on the targets of productivity, manufacturing cost, surface roughness, cutting force fluctuation optimization model, according to research of the high speed milling parameters selecting restrict of work piece, machine, tool and safety, set up high speed milling parameters multi-object optimization system.

本文以已有的高速铣削机理及高速刀具技术研究成果为基础，结合高速铣削试验，进行了基于遗传算法的高速铣削参数优化研究与系统开发，主要的研究内容为：通过高速面铣刀和高速立铣刀加工铝合金和铸铁等材料的切削力和表面粗糙度试验，进行了铣削速度、每齿进给量、铣削深度和铣削宽度对高速铣削加工过程影响的研究；采用多元线形回归的方法，建立了切削力及其振幅和表面粗糙度模型，并对模型的显著性进行验证，为高速铣削参数优化模型的建立奠定了基础。

The precision lapping technology to machine the copper substrate using semi-fixed abrasive plate was studied. The surface roughness and material removal rate as the evaluation of indicators, the influences of the different lapping parameters on the surface roughness and material removal rate were discussed and analyzed. Experimental results indicated that the copper substrate could be efficiently machined by semi-fixed abrasive plate of 800(superscript #) SiC abrasive, and the initial roughness Ra of a machined surface could be improved from 0.553μm to 0.28μm in 10min, produced an ideal rarely scratch surface. Then processed copper polished by diamonded grinding paste, it could be satisfied for the Ni-Pd-P alloy thin film growth.

主要研究半固着磨具精密研磨非晶态Ni-Pd-P合金薄膜铜片衬底，以铜片衬底的表面粗糙度和材料去除率为评价指标，探讨了研磨过程中不同的工艺参数对铜片表面粗糙度和材料去除率的影响结果表明：用800 SiC半固着磨具对铜片衬底进行研磨加工，10min后铜片表面粗糙度Ra可由0553μm减小到0.28μm，同时表面无深划痕：加工后的铜片再经金刚石研磨膏抛光可快速获得满足Ni-Pd-P合金薄膜生长用的铜片衬底表面。

Cylinder, the cylinder sets of radial a surplus deformation of the cylinder sets a great impact on the cylinder liner reduced radial a surplus amount to reduce the deformation of the cylinder sets, the top surface of the body decreases roughness, but it will increase the body on the plane cylinder only mouth the roughness ; Preload reduced cylinder head bolt deformation of the cylinder liner little effect, the body can reduce the top surface roughness and cylinder body on the plane I ended roughness; Shen appropriate reduced cylinder head bolt hole deep can reduce the deformation of the cylinder sets, but will cause the body and the top surface roughness on the cylinder body only I roughness increases Plane .

工作工况下，对于第2缸来说，气缸套径向过盈量对气缸套变形影响很大，减小气缸套径向过盈量，有利于减小气缸套的变形，减小机体顶面不平度，但会增大机体上缸套止口平面的不平度；减小缸盖螺栓预紧力对气缸套变形影响很小，可减小机体顶面不平度和机体上缸套止口平面的不平度；适当减小缸盖螺栓沉孔深可以减小气缸套的变形，但会造成机体顶面不平度和机体上缸套止口平面不平度的增大。

Basic symbols;Coatings;Definition;Definitions;Dimensions;Drawing specifications;Drawings;Engineering drawings;Finishes;Geometric;Geometrical product specification;GPS;Graphic representation;Graphic symbols;Inscriptions in a drawing;Letterings;Machining;Machining tolerances;Marks;Product specifications;Production processes;Products documentation;Ratings;Reference length;Reference lines;Representation of characters;Roughness;Roughness value;Specification;Statement;Surface properties;Surface roughness;Surface texture;Surface treatment;Surface-roughness measurement;Surfaces;Symbols;Technical drawing;Treatment;Wear-quantity

中文标题产品几何量技术规范。技术产品文件中表面结构的表示方式中文主题词图形表示；参考长度；尺寸；加工公差；表面性质；产品规范；覆层；制图规范；精整；表面粗糙度；粗糙度；表面粗糙度测定；表面结构；磨损量；图纸标题；表面处理；技术制图；几何的；基准线；图形符号；符号；标记；加工工艺；文字书写；产品文件；定义；表面；粗糙度值；工程图；额定值；产品几何量技术规范；GPS；叙述；处理；图纸；机械加工；字符表示；基础符号；规范验收

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。