查询词典 rotating speed

Because the workpiece is in dynamic balance, the resultant moment acting on it should be zero. Introducing the moment from lapping tool and press head a moving differential equation is built. In this equation only workpiece rotating speed is unknown. It means that workpiece rotating speed can be got by this equation. Since there is a transcendental function in integral function of the equation an analytic result can not be got, only digital result can be got by a computer. Thus a change rule of workpiece rotating speed with lapping parameters is known, e.g. the radius of press disc ball socket, radius of press head ball, the distance between the workpiece rotating axis and lapping tool rotating axis, workpiece radius, modulus of elasticity of the press head and press disc, friction coefficients between the lapping tool and workpiece, and between the head and disc, pressure between the lapping tool and workpiece and pressure between the press head and press disc.

因工件处于动态平衡状态，其上所受到的来自于磨具和压头的力矩应相等，将二力矩表达式联立，建立工件运动微分方程，该方程中只有工件的旋转角速度是未知量，因此可以求出工件旋转角速度，但该方程积分式中含有超越函数，得不出解析解，只能通过计算机求出数值解，得出工件旋转角速度随各研磨参数的变化规律，如压盖球座半径、压头的球头半径、工件回转中心相对磨具回转中心的偏心距、工件半径、压头和压盖材料的弹性模量、磨具与工件间的摩擦系数、压头压盖间的摩擦系数、磨具与工件间的压强、压头压盖间的压力等。

When rotating speed of the tie bar is 132r/min, according to coarse or fine lapping processes, the rotating speed of the ring gear should be between 31~54r/min.

当系杆的转速设定为132r/min时，根据粗、精研磨不同的工艺要求，其内齿轮的转速应在31~54r/min调整。

When the other parameters are fixed, the SSD can be decreased with the decrease of wheel infeed, the increase of wheel rotating speed and the increase of chuck rotating speed, and the increase of chuck rotating speed within a suitable range.

在一定的范围内，当其它磨削参数不变时，硅片的损伤深度随着砂轮进给率的增大而增大，随着砂轮转速的增大而减小，随着工作台转速的增大而减小。

The calculation results shows that ,(1) when the rotor rotates at the working speed, a local regurgitant whirlpool that is rightabout to the rotor"s rotating direction appears in the classifying region, which makes the separated granules come back to the outside of the classification district and influences the classification efficiency of the turbine classifier;(2) in the condition of a low rotating speed of turbo rotor, ultrafine particles can follow the gas phase by and large, but when the rotating speed increases, a phenomenon of velocity slippage between two phases appears evidently;(3) A operating parameter, air flow rate is so important that can directly influence the stability of flow field in classifying chamber, the bigger the air flowrate is , the steadier the flow field is;(4) Compared with straight blades, the new shape of blades with backward crooked elbow are helpful to improve the stability of flow field and form whole stream easily, also beneficial to advance the classification accuracy and classification efficiency;(5) The motion trace of particles are very complicated when the turbo rotor rotates at a high speed, the constant bounce of the particles appear between the blades and the coarse particles are even bounce back from the inlet, only the finer can pass through the classification area from the oulet;(6) Along with the increase of the rotor"s rotating speed, radiah axial and tangential velocity all begain to fluctuate repetitively like sine-wave, the smaller the particles are, the more violently they fluctuates.

数值模拟结果表明，(1)在涡轮达到工作转速时，在分级区域形成了一个与涡轮旋转方向相反的局部回流涡，它使得分离出来的细粒重又被带回分级轮外边缘，从而严重影响分级机的分级效率；(2)粉尘粒子在涡轮低速运动情况下，基本上能跟随气体运动，但随着转速加大，两相之间出现了明显的速度滑移现象；(3)分级机工作时的风量也是一个比较重要的操作参数，它可以直接影响到分级机内腔流场的稳定性，风量越大，流场越稳定；(4)同直叶片形状相比较，带后弯导板的叶片，有利于改善流场的稳定性，流场容易形成整体流，对提高分级效率和分级精度都非常有利；(5)粒子轨迹线在涡轮转速较高时十分复杂，有的出现了反复的弹跳现象，大颗粒不能通过分级区域而从进口返流了，只有细小的颗粒才从出口处流出；(6)涡轮转速加大时，粒子的径向、轴向和切向速率出现了明显的类似于正弦波的脉动现象，颗粒越小，脉动程度越为剧烈。

The analysis results indicate that the vibration fractional factor with rotating frequency has a close relationship with both rotating speed of rotor and damping of bearing under constant acceleration. When rotating acceleration is small and damping is large, the transient response is not sensitive to the variation of rotating speed; otherwise the imbalance response with constant acceleration and the response in stable state will build up obvious differences near critical rotating speed.

研究结果表明：在恒加速条件下，转子同频振动分量与转子的转速、支承阻尼等因素密切相关，当角加速度较小且阻尼较大时，其瞬态响应对转速的波动不敏感；而当角加速度较大或阻尼较小时，恒加速过程不平衡响应与稳态响应在临界转速附近将产生明显的差异。

The complete wind turbine speed control firstly proposed here also improves the tracking effect of wind turbine rotating speed to variable wind speed. Wind turbine rotating speed synchronized power observer compensates the power ripple of wind turbine resulted in inverter dead time. A low pass filter used at the output of MPPT controller smoothes the speed reference, which makes the rotating speed of wind turbine more stable.

本文首次提出的变转速扰动的MPPT控制提高了风车最大功率点追踪的快速性和稳定性，风车完全转速控制提高了风车转速对变动风速的跟踪效果，转速同步风车功率观测法消除了逆变器死区所造成的风车功率波动的影响，带有低通滤波器的MPPT控制器使得风车的转速更加趋于平稳。

A mixed sensitivity H∞ control model is constructed and the band width of wind turbine speed control is designed according to the frequency characteristic of wind speed variation and noise of rotating speed sensor. The sensitivity function is decreased within this frequency band to restrain the wind torque perturbation to wind turbine rotating speed control.

通过构造基于复合灵敏度的H∞鲁棒控制模型，根据风速的波动频率范围和传感器的噪声频率范围设计了风车转速控制的带宽，并在此带宽内降低系统的灵敏度函数，来抑制风力转矩对风车转速控制的干扰。

The rub-impact between rotor and stator often occurs because the rotor shaft stiffness decreases following the occurrence of the crack in the rotor shaft, and thus the coupling fault with rub-impact and crack is hackneyed fault type. Based on the nonlinear dynamical model of the cracked rotor-bearing system with rub-impact, the stability of the periodic motion and instability way were studied in unbalance-rotating speed plane and rotor/stator clearance- rotating speed plane and crack depth- rotating speed plane, and the main results were validated by the experiment.

转子轴承系统裂纹故障的出现会引起转子系统转静件之间碰摩故障的发生，因此裂纹碰摩耦合故障也是转子系统常见的故障类型，本文在裂纹碰摩耦合故障转子轴承系统的非线性动力学模型基础上，分析了系统在不平衡量-转速、碰摩间隙-转速、裂纹深度-转速等参数域内，周期运动的稳定性及其失稳规律，并用实验验证了主要理论结果。

Some concrete suggestions for increases of packing fraction and rotating speed are presented, the rotating speed is 11.3% higher than the supercritical one by data analysis, which results in yield increasing and energy consumption decreasing within the optimum rang of rotating speed.

提出增加充填率和加快转速的具体措施。尤其是通过数据分析确定该机转速超过其临界转速11.3%左右，在最佳转速区段，其增产节能降耗效果最佳。

Such raw materials as waste polyethylent cable particles, pure polyvinyl chloride powder, wood powder, a metallic soap stabilizer, a coupling agent, chlorinated polyethylene and methacrylic acid polyesters and a lubricator are added into and mixed in a high speed mixer according to the formula, and the mixing temperature is 100 to 110 DEG C, the mixing time is 20 to 35 min; the well mixed material is added into an extruder for extrusion, the rotating speed of the mainframe of the extruder is 40 to 60r/min, the rotating speed of a feeding machine is 4 to 6r/min, and the materials are shaped after being extruded.

将废旧聚氯乙烯电缆颗粒、纯聚氯乙烯粉、木粉、金属皂类稳定剂、偶联剂、氯化聚乙烯、甲基丙烯酸多元酯、润滑剂按照配方配制的原料加入高混机中混合，混合温度为100℃～110℃，混合时间为20～35分钟；将混合好的原料加入挤出机中进行挤出，挤出机主机转速为：40～60转/分钟，喂料机转速为：4～6转/分钟；挤出后进行定型。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。