查询词典 rolling

Rolling mill is the most important equipment on the rolling line, and the main transmission system is the nucleal components of the rolling mill.

轧机是轧制线上的重要单体设备，而轧机主传动系统又是轧机的核心组成部分。

The bulging of ingot with a liguid core during rolling is the plastic bending of its solidified shell as a result of a liguid core pressure and a rolling pressure on ingot,which is one of the main deformation characters of the rolling in an unsolidified state.

液芯钢锭轧制过程中产生鼓肚，是由于在液芯内压力和轧制压力的作用下，钢锭凝固壳产生塑性弯曲变形的结果，它是液芯钢锭最主要的变形特点。

The rolling wheel of D51 rolling loop machine is fixed with an expansion ring and its axial locating accuracy is high so the processing difficult of rolling wheel is reduced.

D51型辗环机辗压轮系采用涨圈固定，轴向定位精度高，简化了辗压轮的机械加工；下支承轴端圆锥孔后面设有方孔，辗压辊与下支承轴的联接可靠，更换容易，减少了非生产性工作消耗，提高了劳动生产率。

Secondly, aiming at the difficulty of information sharing between reheating furnace and roughing mill which is brought by the separate control of the two facilities, and the problems of exceeding energy consumption and low security of rolling process given by the difficulty to adjust the heating process of slab dynamically, this paper presents a comprehensive optimizing control strategy of reheating furnace based on the rolling information feedback. In the presented strategy, fuzzy control and neural network are used to feed roll force and slab temperature of therolling process back to reheating furnace and the concrete furnace temperature setting compensation value can be worked out. So that the heating process of slab can be adjusted dynamically according to the heating quality of the slab, and energy consumption can be reduced, the rolling security can be ensured as well.

其次，针对目前加热炉和粗轧机的分离控制带来的生产信息难以共享、钢坯的加热过程难以动态调整而造成的能耗浪费过大、粗轧机轧制安全难以保障等问题，提出了基于轧制信息反馈的加热炉综合优化控制策略，利用模糊控制和神经网络的方法，将粗轧机一侧的能够反映钢坯加热质量好坏的生产信息，如粗轧机的轧制力、钢坯的温度等，反馈到加热炉一侧并计算出炉温设定值的补偿量，从而能够根据钢坯的加热状况动态地调整后续钢坯的加热过程，减少了能耗浪费，保障了轧制安全。

Combined hourglass control in analysis of cold ring rolling process;2. Recent status and development of real-time measurement and online control technology in cold ring rolling ;3. The influence law of feed rate of idle roll on the quality of end face of ring,axial width spread ratio,roll force,roll moment and metal flow characteristic in cold ring rolling process has been explored through the FEM numerical simulation of the ring with rectangular cross-section based on the elastic-plastic dynamic explicit FEM under the Abaqus software environment.

基于Abaqus/Explicit提供的显式动力学有限元算法，对矩形截面环件冷辗扩进行了有限元数值模拟，揭示了芯辊进给速度对环件冷辗扩过程中环件端面质量、轴向宽展率、辗扩力、辗扩力矩以及金属流动特性的影响规律，并从金属塑性成形原理和塑性加工力学等角度对这些规律进行了合理的解释，从而获得了进给速度对冷辗扩成形的影响规律，为环件冷辗扩在实际应用中进给速度的选择提供了依据，对揭示冷辗扩成形机理也具有十分重要的意义。

The paper introduces hot strip rolling lubrication mechanism,analyzes r easons which effect hot rolling lubrication,and put forward to opinions to furth er improve the effect of hot rolling lubrication.

介绍了板带热轧润滑的机理，分析了影响热轧润滑使用效果的因素，同时提出进一步改善热轧润滑效果应重视的问题。

A new process for seamless tube production called Seamless Tube Process comes into our horizon. The key equipment is a four—roll planetary rolling mill, which is also called Kocks Reduction Mill. The structure and operation principle of four-roll planetary rolling mill is similar to the three-roll planetary rolling mill.

最近出现了一种新的轧管工艺——STP轧管工艺，其核心设备为四辊行星轧机，又称KRM轧管机，其结构和工作原理与三辊行星轧机类似。

The formation of billet steel rocker was calculated theoretically and analyzed using the differential method of rolling pressure along width in rolling deformation zone according to the position of the billet steel skid mark,the asymmetrical distribution of the mark degree and the departure of rolled piece centerline from the centerline of rolling.

在轧制变形区应用轧制压力宽向微分法，从钢坯滑道黑印位置和黑印程度的非对称分布、轧件中心线偏离轧制中心线两方面对钢板镰刀弯的形成进行了理论计算和分析，提出了改进操作规程、提高推床适应能力、改进加热炉滑道、加强加热工艺技术管理以及实施热送热装提高热坯的供应能力等多项措施，以适应多倍尺轧制工艺的要求。

Plate mill rolling procedure calculation system was developed according to process of plate mill and requirement of engineering design, rolling temperature and force and power model was supplied, rolling procedure calculation system was introduced.

结合宽厚板轧机生产工艺特点及工程设计需要，开发了宽中厚板轧制规程计算软件，对宽厚板轧机轧制过程温度及力能参数计算模型公式的选用、计算方法及编程过程等进行了介绍。

The three-dimensional models of rolling are established with Pro/E. Based on the finite element analysis software ANSYS/LS-DYNA, the procedure of bar tandem rolling is simulated. The nephograms of stress and strain of bar deformed area and the curve of roll force during rolling are obtained.

以三维立体软件Pro/E为平台，对其进行实体建模，并以大型商用有限元软件ANSYS/LS-DYNA为分析工具，对棒材连轧进行模拟，得出轧制过程中棒材变形区的应力、应变的变化情况和轧制力曲线。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。