查询词典 rolling

Considered the inside and outside contour line was Archimedes spiral in the cold rolling, the forming law of rectangular cross sectional rings has been studied. And the more precise geometrical models and calculation models have been gained. The researches can be used as a theoretical and experimental foundation for the simulation of ring rolling process. At the same time, the results of theoretical analysis have a good agreement with the results of practical rolling production.

本文在考虑冷轧过程中环件的内外轮廓线均为阿基米德螺线的情况下，对矩形截面环件的轧制成形规律进行了研究，得到了较精确的几何模型和计算模型，为环件轧制过程的模拟提供了理论依据和实验依据，同时理论分析的结果与实际轧制生产过程中的结果有较好的吻合。

In th e case of more and more higher precision of armor plate, more and more complex control parameter of rolling mill and the emergence of all sorts of high and new rolling technology, it is more exigent to research in-depth the theory of rolling.

在行业对于钢板的精度要求越来越高，轧机的控制参数越来越复杂，各种高新轧制技术不断出现的形势下，对于轧机理论的深入研究也就更加迫切。

Rolling pressure and rolling torque are important technical parameters in rolling course. They play an important role in establishing depression regulation, analysis of load in working procedure, checkage of equipments intensity and so on.

轧制压力和轧制力矩是轧制过程中重要的工艺参数，在制定压下规程、工序负荷分析、设备强度校核等方面都具有重要作用。

Rolling load, rolling forceCadillac's 2000 DeVille, rolling out this fall, is the first vehicle to carry the system.

今年秋季就将大批生产的卡迪拉克帝威2000型汽车就是第一批携带夜视装置的车辆。

The rolling procedure of cross wedge rolling in the case of die void and not was simulated adopting Finite element method. Base on it, effect of die void on rolling force was analyzed in detail.

为此，采用有限元法对楔横轧模具在不脱空和脱空情况下进行了轧制过程数值模拟，详细分析了模具脱空对轧制力影响的规律，得到了在一定断面收缩率范围内模具脱空有利于减小轧制力的研究结果，并与测试结果进行比较。

It analyzes contradiction on applicable location of fire resistance rolling screen in GB 500045-95 with reality,puts forward two solutions,and introduces countermeasures for quality of fire resistance rolling screen and technical supervision to display function of fire resistance rolling screen .

分析了GB 50045-95中关于防火卷帘的适用场所这一规定在现实当中出现的矛盾，并提出了解决矛盾的两种办法，介绍了解决防火卷帘质量及技术归口监督问题的对策，以发挥防火卷帘的正常功能。

The results show that the quantity of duplex impurity in CSP thin slab is minute. The size of crystal grain of the steel strip side along the width direction during continuous casting and continuous rolling,cold rolling and annealing is finer than that of the steel strip center and the phenomenon is more obvious duing continuous casting and continuous rolling than during other processes.

结果表明：包钢CSP薄板坯中复合夹杂的数量极少，在CSP连铸连轧及后续的冷轧薄板生产过程中，铸坯、热轧板、冷硬板和退火薄板沿宽向边部的组织均较中部的组织细小，且铸坯和热轧状态下较为明显。

But at present in our country the rolling mill utilization ratio and the output compares with units energy consumption hour of the Middle-thicken Plate are very low. Especially in the stage of rough rolling, because of utilization rate of equipment is not enough the rolling cycle of each steel is too long, thus it result in lower producing and more energy consumption.

但目前国内中厚板轧机利用率，小时产量和单位能耗比都较低，尤其对于中厚板生产粗轧阶段由于设备利用率不够，每块钢的轧制周期时间太长，从而导致产能低，能源消耗大的情况。

Wind tunnel investigation is conducted on six different canard configuration models over range of Mach from 0.8 to 2.5.The experiment data analyzes the regulation of rolling characteristics with Mach number and angle of attack,and the effect of rolling characteristics for different configurations is discussed.The rolling damping characteristics are also studied.

通过风洞实验得到了跨、超音速下六种组合模型的气动力数据，由实验结果分析了远程弹滚转特性随马赫数和攻角的变化规律，以及不同鸭式气动布局对滚转特性的影响，此外还分析了远程弹的滚转阻尼特性。

The planning of the processing parameter is based on the plastic deformation of the metal because the planning of the cold rolling technique is affected by the ability plastic deformation of the metal. Industrial PC is the master processor of the cold rolling machine. The process of cold rolling monitored by the corresponding functional component real-timely.

冷辗工艺的设计受金属塑性变形能力的影响，因此工艺参数设计以金属塑性变形为基础；冷辗机控制系统以工业PC为主控制器，通过相应的功能模块实现对冷辗进程的实时监控。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。