查询词典 rolling-over

Rolling load, rolling forceCadillac's 2000 DeVille, rolling out this fall, is the first vehicle to carry the system.

今年秋季就将大批生产的卡迪拉克帝威2000型汽车就是第一批携带夜视装置的车辆。

The rolling procedure of cross wedge rolling in the case of die void and not was simulated adopting Finite element method. Base on it, effect of die void on rolling force was analyzed in detail.

为此，采用有限元法对楔横轧模具在不脱空和脱空情况下进行了轧制过程数值模拟，详细分析了模具脱空对轧制力影响的规律，得到了在一定断面收缩率范围内模具脱空有利于减小轧制力的研究结果，并与测试结果进行比较。

It analyzes contradiction on applicable location of fire resistance rolling screen in GB 500045-95 with reality,puts forward two solutions,and introduces countermeasures for quality of fire resistance rolling screen and technical supervision to display function of fire resistance rolling screen .

分析了GB 50045-95中关于防火卷帘的适用场所这一规定在现实当中出现的矛盾，并提出了解决矛盾的两种办法，介绍了解决防火卷帘质量及技术归口监督问题的对策，以发挥防火卷帘的正常功能。

The results show that the quantity of duplex impurity in CSP thin slab is minute. The size of crystal grain of the steel strip side along the width direction during continuous casting and continuous rolling,cold rolling and annealing is finer than that of the steel strip center and the phenomenon is more obvious duing continuous casting and continuous rolling than during other processes.

结果表明：包钢CSP薄板坯中复合夹杂的数量极少，在CSP连铸连轧及后续的冷轧薄板生产过程中，铸坯、热轧板、冷硬板和退火薄板沿宽向边部的组织均较中部的组织细小，且铸坯和热轧状态下较为明显。

But at present in our country the rolling mill utilization ratio and the output compares with units energy consumption hour of the Middle-thicken Plate are very low. Especially in the stage of rough rolling, because of utilization rate of equipment is not enough the rolling cycle of each steel is too long, thus it result in lower producing and more energy consumption.

但目前国内中厚板轧机利用率，小时产量和单位能耗比都较低，尤其对于中厚板生产粗轧阶段由于设备利用率不够，每块钢的轧制周期时间太长，从而导致产能低，能源消耗大的情况。

The planning of the processing parameter is based on the plastic deformation of the metal because the planning of the cold rolling technique is affected by the ability plastic deformation of the metal. Industrial PC is the master processor of the cold rolling machine. The process of cold rolling monitored by the corresponding functional component real-timely.

冷辗工艺的设计受金属塑性变形能力的影响，因此工艺参数设计以金属塑性变形为基础；冷辗机控制系统以工业PC为主控制器，通过相应的功能模块实现对冷辗进程的实时监控。

The rolling theory deals only with simple rolling condition. But, in fact, any rolling process has, more or less, some nonsymmetry.

根据轧制理论，在普通四辊轧机上轧制薄带钢时，常被认为相当接近于简单轧制条件，这时两轧辊上的轧制力矩相等。

Analysis of application effect proves that strip flatness error can be well controlled in the scope of 0～3 I in stable rolling condition and close loop feedback control method satisfies the need of high precision control for cold rolling strip flatness. cold rolling ; Clecim AFC system ; multivariable optimum control

本文对国内某厂引进的Clecim冷轧AFC系统的控制原理和控制特点作一介绍，并对实际的板形控制效果进行分析说明。1闭环反馈控制原理Clecim冷轧AFC系统的控制原理如图1所示，板形检测值与目标板形相比较得到板形误差分布，通过多变量优化控制求

After introducing 56Nb steel, in order to meet performance requirement of 56Nb steel fish plate on the railroad rail, the production technique of 56Nb steel fish plate has been adopted under the factory equipment conditions: 450 kg steel ingot is prepared by melting in 8 t arc furnace and casting at 1 570-1 580℃ which is heated to 1 250-1 270 ℃, trimmed to 185 mm×195 mm bloom after rolling by 600 series 2-stand rolling mill; then rolled 15 times by 600 series 2-stand rolling mill when steel ing

介绍了56Nb钢后，根据铁道接头夹板的性能要求并结合厂方的设备状况制定了56Nb钢鱼尾板材料的生产工艺：用8 t电弧炉冶炼，于1 570～1 580℃下铸成450 kg钢锭；将钢锭加热到1 250～1 270℃，经600系列2机架轧机5道次轧制后修整成185 mm×195 mm方坯；再将钢坯加热到1 050～1 150℃，由600系列轧机（2机架）共15道次轧制，用350系列（3机架）精轧机经3道次精轧成60 kg/m的鱼尾板材料，终轧温度约900℃。

At first, on the basis of the combination research methods of analytical theory, numerical simulation and experiment, the mathematical and physical model of certain-length rolling process have been established. Then according to the established model, the menstruation of rolling average friction coefficient is proposed; and then the certain-length rolling process and key parameters are determined.

采用理论研究、数值模拟和实验研究相结合的研究方法，建立定长轧制物理模型和数学模型；基于所建模型，提出了一种测定轧制平均摩擦系数的方法；确定了定长轧制工艺方法和关键参数；分析了影响制件轧制长度的因素；对关键参数进行了数值模拟。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新