查询词典 rolling mill

A ragging mechanism is added to the common C8463A roll lathe,and PLC is adopted mainly to carry out electric control,and then the ragging can be nicked on the bottom of the pass of φ500mm rolling mill roll.

在普通C8463A轧辊车床上增加一套凸痕机构，并以PLC为核心进行电气控制，解决了在φ500mm轧辊孔型槽底刻制凸痕的问题。

In this paper, some factors affecting the finished product rate of CSP are analyzed, including the number of continuous-continuous casting heat, breakouts in casting, failures to start a casting process, accidents with rolling mill, molten steel remainders in ladle and tundish, and the percentage of abnormally termin...

本文对影响CSP短流程成材率的各个因素进行分析，包括连浇炉数、连铸漏钢与开浇失败等事故、轧机事故、大包中包注余、非正常终浇比例等，并分析了实际生产中影响成材率的各种情况，提出了提高电炉CSP短流程成材率的措施。

Morgan Construction Company and its subsidiary company in china Morgan Rolling Mill Co., Ltd have been acquired by Siemens VAI which is located in Linz, Austria and belongs to Industrial Solutions Division of Siemens AG. Morgan.

美国摩根工程公司及其在中国的子公司－摩根轧机有限公司，于2008年4月被西门子公司兼并，由西门子集团公司行业解决方案部门旗下一个总部位于奥地利林茨的业务分部西门子奥钢联冶金技术公司进行管理。

It has the advantages of high accuracy,high efficiency,low noise and easy service.It can be used individually or with rolling mill or uncoiling machine to form production line.

该机精度高、效率高、噪音低、使用维修方便，可单机使用，也可与各类轧机或板、带材制品开卷设备配套组成流水线。

Based on this discovery this dissertation presented that the torsion rigidity of the cross axle type universal shaft must be taken into account when researching the main transmission system of the rolling mill.

并依此提出了在研究轧机主传动系统的扭转振动时，必须计及十字轴式万向联轴器的扭转刚度的观点。

BEM for elastio-plastic contact problem is employed to study the deformation and loading station of the sleeve and roller neck of film bearing in rolling mill under special way of assembly in this paper.

利用弹塑性接触问题边界元法分析了轧机油膜轴承锥套与轧辊辊颈装配过程中的变形和载荷特性，讨论了接触应力和变形对锥套与辊颈损伤的影响，给出了防止锥套与辊颈装配过程损伤的具体改进措施。

Products are widely applied to various: bend, water, stamping products, electronic products, and promptly, pen holder, piston, banding belt, clamp, toys, kitchen equipment and accessories, frame, welcome, vortex spring, tape, timer and starter, etc Our company owns advanced equipment and technology, high precision rolling mill, slitting machine, twisted, polishing machine, mirror 8K machine, automatic cutting machine, heat treatment, such as wind forming machine equipment, high precision instrument parts.

产品表面有2B，BA，2B光亮，8K镜面等，产品广泛应用到各类：折弯，水涨，冲件制品，电子产品、制管、弹片、笔夹、活塞环、捆扎带、卡箍、玩具、厨房设备、纺织机配件、综丝、洗尘器、涡形弹簧、卷尺、定时器和启动器等我公司拥有先进的设备和工艺、高精度轧机、分条机、拉绞机、抛光机、镜面8K机、自动剪切机、热处理流水线、发条成形机等设备以及高精度的测试仪件器。

Works on the bending roll system of four-roll rolling mill, the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the FEM software ANSYS, the maximum deformation of the work roll was calculated, and the curve of the gap adopting the Least-Squares method was fitted, which set the base of the further calculation of load-gap shape.

以四辊轧机的弯辊系统为研究对象，利用有限元分析软件ANSYS研究弯辊力和辊间接触应力引起工作辊形状的变化，计算工作辊弯曲的最大变形量，并用最小二乘法对辊缝曲线进行拟合，为进一步计算有载辊缝形状提供可靠的理论依据。

A high speed line material vertical rolling mill framework moderating machine gearbox of Hunan steel Co., Ltd, the gear teeth of the first transmission spiral bevel wheel were broken.

詹仁杭，轧立式轧机减速机螺旋伞齿轮断齿原因分析湘钢一高速线材粗中轧立式机架减速机齿轮箱，第一级传动螺旋伞齿轮轮齿断裂。

Keywords high speed line material;vertical rolling mill;moderating machine;spiral bevel wheel;computational analysis;unreasonable structure;improving suggestion

高速线材；立式轧机；减速机；螺旋伞齿轮；计算分析；结构不合理；改进意见

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。