查询词典 rolling list

This experiment is the Chinese character dot matrix rolling process, shows a Chinese rolling process.

本实验是点阵的汉字滚动程序，显示的一个汉字滚动程序。

Rolling load, rolling forcea cgs unit of work or energy; the work done by a force of one dyne acting over a distance of one centimeter.

厘米克秒制功或能单位；一个一达因的力使物体沿力的方向通过一厘米的距离所做的功。

The rolling effects of horizontal and edger rolls were both taken into account during load distribution, and iterative computations were done alternately along the width and thickness of work piece by virtue of the equal load function to optimize the rolling schedule step by step.

分配时兼顾水平辊和立辊轧制的影响，在宽度和厚度两个方向进行等负荷函数的交替迭代计算，逐步优化规程，并在外层迭代中设置了机组轧制负荷超限情况下的道次数自动修正。

Generally, its operating condition is under the low-speed and thin oil lubrication, so the viscous friction was usually neglected and the friction torque caused by main influencing factors of elastic hysteresis in rolling, spin of rolling element and sliding friction on contact zone were considered.

低速灵敏球轴承小而稳定的启动力矩和动态力矩对于导航系统的姿态控制至关重要，其工况通常是低速稀油润滑，黏性摩擦被忽略而重点推导接触区因弹性滞后、自旋及差动滑动引起的摩擦力矩。

Kids will enjoy rolling the fondant on the work mat with the rolling pin.

孩子们将享受滚动达特的工作与垫擀面杖。

The article introduces the technical requirements, experimental rolling processes, existing problems and improvement measures of the 25MnCrNiMoA round steel used for forging hook tail frame developed in the Rolling Plant.

介绍了轧钢厂开发的25MnCrNiMoA锻造钩尾框用圆钢的技术要求、轧制试验工艺、存在的问题和改进措施。

New multi—objectives function (including mill stand longitudinal stiffness, distribution coefficient of loaded pressure between rolls, weight of mill stand, rolling power, rolls loaded gap profile changeability of bending force, transverse mill stand stiffness of bending force, transverse mill stand stiffness of rolling load) multi—constraints (including rolls strength, spindle strength, backup roll bearing load, minimum rollable gauge, roll surface temperature rise) rolls system parameters optimization model of four—high cold strip mill is established, and programme for mill structural illustration creation on the platform of AutoCad designs is compiled. With this as basis, rolls system parameters of Yichang thin strip corporation's 1219 cold mill are calculated using SUMT (subsequent unconstrained minimization technology).

本文建立了以板形和板凸度控制特性为目标的四辊轧机多目标函数（包括轧机纵向刚度、辊间压力分布系数、轧机重量、功率、弯辊力对轧机辊缝形状改变能力、对弯辊力的横向刚度、对轧制力的横向刚度）、多约束条件（包括轧辊强度、接轴强度、支承辊轴承负荷、最小可轧厚度、轧辊温升等）的辊系参数优化模型，以此模型为基础，利用惩罚函数法计算了益昌薄板公司1219冷轧机辊系参数，编制了AutoCAD平台下的轧机结构示意图自动图形软件。

Part of the normal roller, the fault is not resolved, check for roller pressure, which can use FUSE (electrical purposes 20, fusealways) and qianyanzhou hobber in rolling direction, not to mention the occipital clearance to unload their plates and blankets, the slot for the Department in the roller snthase pad, if rolling pillow gap over specification number, the adjustment of the diaphragmless, the pillow are met at both ends of the clearance requirements, you can troubleshoot.

墨辊局部变态了，障碍仍未处置，再查抄滚筒之间的不张力，可用电工用不焊接丝（20号保障丝）和千分卡轧测滚枕间隙，必须卸下印版和橡皮布，在滚筒的不满档处分不抬轧测，若滚枕间隙超功表明书规矩的数值，则调动调不抬器，使滚枕两头间隙都相符表明书上的请求，即可摈斥障碍。

Roll pass on angle steel rolling, I-beam rolling and U-section, etc. were intensively studied.

他对角钢孔型轧制的，工字钢轧制和U -型钢轧制等剧做过深入研究。

To sette plate bending in jobbing sheet rolling process make use of test technology comprehnsive parameters are tested in jobbing sheet rolling process when plate bending.

中板轧制过程板坯弯曲现象是中板生产中普遍存在的难题。针对这一问题，利用测试技术对中板轧制过程板坯生成弯曲时的轧制参数进行了综合测试，摸清了轧制参数的变化规律及特点，为板坯弯曲的机理研究和设备改造提供了可靠的科学数据

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48