查询词典 rolling hitch

But at present in our country the rolling mill utilization ratio and the output compares with units energy consumption hour of the Middle-thicken Plate are very low. Especially in the stage of rough rolling, because of utilization rate of equipment is not enough the rolling cycle of each steel is too long, thus it result in lower producing and more energy consumption.

但目前国内中厚板轧机利用率，小时产量和单位能耗比都较低，尤其对于中厚板生产粗轧阶段由于设备利用率不够，每块钢的轧制周期时间太长，从而导致产能低，能源消耗大的情况。

Wind tunnel investigation is conducted on six different canard configuration models over range of Mach from 0.8 to 2.5.The experiment data analyzes the regulation of rolling characteristics with Mach number and angle of attack,and the effect of rolling characteristics for different configurations is discussed.The rolling damping characteristics are also studied.

通过风洞实验得到了跨、超音速下六种组合模型的气动力数据，由实验结果分析了远程弹滚转特性随马赫数和攻角的变化规律，以及不同鸭式气动布局对滚转特性的影响，此外还分析了远程弹的滚转阻尼特性。

The planning of the processing parameter is based on the plastic deformation of the metal because the planning of the cold rolling technique is affected by the ability plastic deformation of the metal. Industrial PC is the master processor of the cold rolling machine. The process of cold rolling monitored by the corresponding functional component real-timely.

冷辗工艺的设计受金属塑性变形能力的影响，因此工艺参数设计以金属塑性变形为基础；冷辗机控制系统以工业PC为主控制器，通过相应的功能模块实现对冷辗进程的实时监控。

The rolling theory deals only with simple rolling condition. But, in fact, any rolling process has, more or less, some nonsymmetry.

根据轧制理论，在普通四辊轧机上轧制薄带钢时，常被认为相当接近于简单轧制条件，这时两轧辊上的轧制力矩相等。

Analysis of application effect proves that strip flatness error can be well controlled in the scope of 0～3 I in stable rolling condition and close loop feedback control method satisfies the need of high precision control for cold rolling strip flatness. cold rolling ; Clecim AFC system ; multivariable optimum control

本文对国内某厂引进的Clecim冷轧AFC系统的控制原理和控制特点作一介绍，并对实际的板形控制效果进行分析说明。1闭环反馈控制原理Clecim冷轧AFC系统的控制原理如图1所示，板形检测值与目标板形相比较得到板形误差分布，通过多变量优化控制求

After introducing 56Nb steel, in order to meet performance requirement of 56Nb steel fish plate on the railroad rail, the production technique of 56Nb steel fish plate has been adopted under the factory equipment conditions: 450 kg steel ingot is prepared by melting in 8 t arc furnace and casting at 1 570-1 580℃ which is heated to 1 250-1 270 ℃, trimmed to 185 mm×195 mm bloom after rolling by 600 series 2-stand rolling mill; then rolled 15 times by 600 series 2-stand rolling mill when steel ing

介绍了56Nb钢后，根据铁道接头夹板的性能要求并结合厂方的设备状况制定了56Nb钢鱼尾板材料的生产工艺：用8 t电弧炉冶炼，于1 570～1 580℃下铸成450 kg钢锭；将钢锭加热到1 250～1 270℃，经600系列2机架轧机5道次轧制后修整成185 mm×195 mm方坯；再将钢坯加热到1 050～1 150℃，由600系列轧机（2机架）共15道次轧制，用350系列（3机架）精轧机经3道次精轧成60 kg/m的鱼尾板材料，终轧温度约900℃。

At first, on the basis of the combination research methods of analytical theory, numerical simulation and experiment, the mathematical and physical model of certain-length rolling process have been established. Then according to the established model, the menstruation of rolling average friction coefficient is proposed; and then the certain-length rolling process and key parameters are determined.

采用理论研究、数值模拟和实验研究相结合的研究方法，建立定长轧制物理模型和数学模型；基于所建模型，提出了一种测定轧制平均摩擦系数的方法；确定了定长轧制工艺方法和关键参数；分析了影响制件轧制长度的因素；对关键参数进行了数值模拟。

In the paper, the present state of ultra-fine-grained materials, severe plastic deformation and Asymmetrical-ARB are introduced in detail; the craft to fabricate ultra-fine-grained copper using Asymmetrical -ARB is studied fully; the problem of combination of interface is settled; the affect of homogenizing annealing、 annealing and rolling method on mechanical properties of materials prepared by Asymmetrical-ARB is discussed and analyzed when control parameters of rolling mill such as the press—ratio、 the asynchronous rate、 rolling—speed are fixed, and a kind of craft that meets to requirement of experiment is made out.

本文对超细晶、大塑性变形技术、异步轧制目前国内外研究进行了详细的介绍；对异步叠轧方法制备超细晶铜工艺做了较为细致的研究：解决界面复合问题；在压下率、异步比、轧制速度等轧机控制参数固定条件下，探讨了均匀化退火工艺、去应力退火工艺和轧制方式对异步叠轧材料力学性能的影响，并进行了分析，制定出符合实验要求的轧制工艺。

Closed die forging or extrusion, drawing, upsetting, bending or free forging, flat rolling, profile rolling or tumbling cold, hot or semi-hot, mechanical press, hammer or screw press, rolling machine or orbital forging even coupled processes and spring-controlled tools, simple low-alloyed or stainless steel , aluminium or non-ferrous metal, titanium or nickel based alloys, massive or sheets, material flow or dieload analysis

Forming已经成功研制可支持目前所有制造业的软件应用程序，并可独立的仿真金属温度，机体使用情况或材料的处理：封闭模锻或挤压，钢绘，镦，弯曲或自由锻造，轧制，型材辊压或翻滚-冷，热或半热，机械压力机，锤或螺旋压力机，辗机或轨道锻造-更可加上流程以及spring-controlled工具，简单的低合金或不锈钢，铝或非铁金属，钛镍合金，大规模工程或床单工程，物质流或dieload分析。

Rolling force and moment are the basic technics parameter for Assel rolling mill design,but about it,s technics calculate is very poor currently.one form by dint of approximately calculate, the result unlikelihood .J·kazanecki and domestic scholar according as metal distortion superior limit,gave some formula have some worthiness,but very complexity.the author base on practicality rolling technics, gvie a simpleness calculate means.the result close to measure numerical value,supply some reference value.

轧制力、轧制力矩是设计Assel轧管机最为基本的参数，但是目前关于其工艺计算的理论还很不成熟，只能借助于近似工程计算方法求得，结果往往偏差较大。德国的J·kazanecki和国内的一些学者提出了利用金属塑性变形场的上界法求解上述参数，具有一定的参考价值，但其数学计算相当繁杂。作者从轧制工艺实际出发，遵循塑性力学的基本原理，给出了简便易行的计算方法，具有重要的实际意义。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48