查询词典 rolling friction

Experiments were performed with this device to measure the static coefficient of friction for three kinds of material(45steel,HT35-61,QT80-2) in the same processing method,the same surface texture,the same load,dry friction and different surface roughness conditions respectively.

分别对材料(45钢、HT35-61、QT80-2)在相同加工方法、相同表面纹理、载荷恒定、干摩擦条件下，改变表面粗糙度时的静摩擦因数进行了测定。

The effects of space of fins, number of tube rows and relative humidity of incoming air on airside performance of wavy fin with hydrophilic coating under dehumidifying conditions were experimentally explored for seven wavy fin-and-tube heat exchangers with hydrophilic coating. The Colburn factor and the Fanning friction were applied to describe airside heat transfer and friction characteristics, respectively.

为了确定翅片间距、管排数和入口空气相对湿度等参数对析湿工况下带亲水层波纹翅片空气侧特性的影响，对7个带亲水层的波纹翅片管换热器进行了试验研究，并分别以Colburn换热因子和Fanning摩擦因子来反映空气侧换热和压降特性。

AbstractThe effects of space of fins, number of tube rows and relative humidity of incoming air on airside performance of wavy fin with hydrophilic coating under dehumidifying conditions were experimentally explored for seven wavy fin-and-tube heat exchangers with hydrophilic coating. The Colburn factor and the Fanning friction were applied to describe airside heat transfer and friction characteristics, respectively.

摘 要：为了确定翅片间距、管排数和入口空气相对湿度等参数对析湿工况下带亲水层波纹翅片空气侧特性的影响，对7个带亲水层的波纹翅片管换热器进行了试验研究，并分别以Colburn换热因子和Fanning摩擦因子来反映空气侧换热和压降特性。

The effects of space of finsnumber of tube rows and relative humidity of incoming air on airside performance of wavy fin with hydrophilic coating under dehumidifying conditions were experimentally explored for seven wavy fin-and-tube heat exchangers with hydrophilic coating. The Colburn factor and the Fanning friction were applied to describe airside heat transfer and friction characteristicsrespectively.

为了确定翅片间距、管排数和入口空气相对湿度等参数对析湿工况下带亲水层波纹翅片空气侧特性的影响，对7个带亲水层的波纹翅片管换热器进行了试验研究，并分别以Colburn换热因子和Fanning摩擦因子来反映空气侧换热和压降特性。

Generally speaking,"cold-water the effect of friction than the" dry cloth friction is better.

一般来说，"冷水磨擦的效果比"干布磨擦要好一些。

Close the valve, the need to open and close with the Coma Berenices two pieces of the sealing surface of the seal formed between certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread between the stem end bearing at and other friction parts of the friction, and therefore must apply the closing force and closing a certain moment, the valve in the open and close the process, the required hoisting hoisting force and moment of change, and its maximum is close to the final instant or open the initial transient.

关闭阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

Close the valve, the need to open and close with the Coma Berenices two pieces of the sealing surface of the seal formed between certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread Automatic Control Valves between the stem end bearing at and other friction parts of the friction, and therefore must apply the closing force and closing a certain moment, the valve in the open and close the process, the required hoisting hoisting force and moment of change, and its maximum is close to the final instant or open the initial transient.

关闭阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

Close discharge valve, the need to open and close with the Coma Berenices two pieces formed between the sealing suce sealing certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread between the stem end Department and other friction parts bearing friction, and must exert a certain degree of closing force and closing moments, PUMP CONTROL VALVE EN700X the valve in the open and close the process, the required hoisting hoisting force and torque is the change, Its maximum is in the closed or open end of the initial transient instantaneous.

关闭放料阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

Dynamic response of sliding structure subjected to earthquake ground motion is calculated with a precise high order direct integration method, and the numerical results are presented in terms of maximum acceleration response spectra of supcrstructure and maximum sliding displacement response spectrum. By comparison with isolating effects of pure-friction base isolation system and resilient-friction base isolation system , it shows that the isolating characteristic of S-LF is superior to P-F and R-FBI. Through analyzing an engineering example, it is observed that the maximum inter-storey shear force and absolute acceleration of sliding structure to earthquake ground motion are very different from those of traditional structures.

提出了一种新型基础隔震模型，即带限位装置的摩擦隔震体系；基于此隔震模型，利用Floquet理论研究地面谐运动下S-LF结构的运动特性；并利用高精度的精细时程积分法，通过对地震作用下S-LF动力响应的计算，绘制了上部结构最大加速度反应谱和基底最大滑移量反应谱，并研究了各种结构参数对隔震的影响；通过与恢复力摩擦隔震系统和纯摩擦力滑移隔震系统的比较表明，S-LF的隔震性能优于P-F和R-FBI；对计算实例的分析发现，地震作用下S-LF结构的层间最大剪力和最大绝对加速度反应分布较一般传统结构有很大区别。

The results indicate that the result of local Coulomb friction model and nonlocal friction model is not too distinctive.

研究结果表明：不考虑表面微凸的情况，局部库仑摩擦模型与非局部摩擦模型的结果差别不大。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48