查询词典 roller

I'm on a motional roller coaster.

我正在一辆运动的过山车上。

In the investigation of Cu-Zn-Al SMA, the influence of quenching speed, shape memory thermal treatment on SME, microstructure and morphologies was discussed. The changes in morphology and interfaces were in situ metallographic observed during thermal cyclings in order to control the degradation of two way shape memory effect . The stabilization of stress induced martensite variants method and the accordingly changes in microstructure were studied in detail. The mechanism was also compared between SSIM and TWME training method. From the above in situ observation results, the interface structure and especially the twin related A: B type variant pair were examined by HREM to clarify the role of movability of interfaces and the changes in variants orientation in inducing the degradation of the TWME. During developing the Ni-Ti-Hf SMA melt spinning ribbon, it was found the morphology and structure embodied the SME and was directly effected by chemical composition and technique factors, such as the different content of Hf, the speed of copper roller rotation and etc. Therefore, the morphology and structure were extensively examined.

在对Cu-Zn-Al形状记忆合金研究中，研究了提高记忆效应的热处理淬火速度、记忆热处理方式对Cu-Zn-Al形状记忆合金组织结构的影响；为了弄清双程记忆效应衰减的原因，原位动态观察了热循环过程中，合金组织形貌及界面的变化；因形状记忆合金必须经记忆训练才能具有双程记忆效应，系统地研究了应力诱发马氏体稳定化训练方法和这种方法引起的双程记忆合金组织结构的变化，比较了它与双程记忆效应训练方法诱发TWME机制的异同；因在原位动态观察中发现界面可动性及两侧变体取向的变化，伴随着记忆效应的衰减，用HREM详细研究了变体的界面结构，特别是A：B型变体界面结构及变体内部结构。

Other differences include an AMG spoiler lip on the boot lid, a roller blind for rear window, Nappa leather appointments for the seats, the top section of the dashboard, the beltlines, the door armrests as well as the centre console and door centre panels.

其他分歧包括AMG的扰流唇对尾部的箱盖，一个卷帘的后窗，纳帕皮革任命的席位，顶部的仪表板， beltlines ，车门扶手，以及中控台面板和车门中心。

Combined with the techniques of roller compaction and welding repair, it has very nice repair function to the backing plate damaged seriously.

它结合磙压、焊补技术对损坏较严重的垫板均具有很好的修复功能。

Variation in the settings between back detaching roller and nipper.

各精梳头后分离罗拉和钳板之间的隔距差异。

In this paper, the combing time, timing of nipper opening-closing, web length of detaching roller reverse feeding and so on parameters are calculated and analysed by computerized of the 112 cylinder combing surface, locations of different cylinders and different noil gauge.

运用计算机对E7/ 6型精梳机采用 112°锡林梳理面及不同的锡林定位、不同落棉隔距时，计算与分析了锡林的梳理时间、钳板的开口定时、分离罗拉倒入机内的棉网长度等参数。

The calculation reveals that 36 index cylinder location, larger noil gauge and later timing of detaching roller cloc...

得出在E7/ 6型精梳机上采用 112°梳理面的锡林时，应采用 36分度的锡林定位、较大的落棉隔距及较晚的分离罗拉顺转定时。

The drive hub (100) has a unitary nonconducting plastic body, with a plug portion (118) for elastically and slidably press-contacting the end of the developer roller, an elongated axle portion (120) with an uninterrupted bearing surface, a shoulder portion for supporting a spring (114), and a longitudinal passage running through the axle and shoulder portions.

该驱动轮毂(100)具有整体的非导电塑性体，该塑性体有一弹性地并可滑动地压接触显影辊的端部的插塞部分(118)；一具有连续支承表面的细长轴部分(120)；一支承弹簧(114)的台阶部分；一经过轴部分和台阶部分的纵向通道。

The nonmotile table by nearby the nonmotile roller barrel module, the aluminum the board, the piece frame, the tension bar, the altar is composed.

无动力辊道由无动力辊桶组件、铝旁板、片架、拉杆、承座组成。

The Winklhofer method is an exact method.But Winklhofer method cannot calculate centerdistance of a roller chain drive whose length of chain is an odd number of chain pitches.Involute function method is anapproximative method.

W ink lhofer方法是准确的计算方法，但只能用于链条总长是链节的偶数倍时的链传动，而渐开线法是近似法，不能精确地计算链传动中心距；而二分法是一种数值法，它可精确地计算链传动中心距，并且适用于链条总长是任意值的链传动，可计算出链传动中心距最大值和最小值。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。