查询词典 roller-skated

As a result of changing perimeter business card printing and membership card product, there is no need to replace a printing plate cylinder, mandril of the roller and gear, reduces Exchange products as a printing plate roller drum and the time it takes.

因此更换不同周长的制卡和会员卡制作产品时，不需要更换印版滚筒、网纹辊的芯轴和齿轮，大大缩短了更换产品时换印版滚简和网纹辊所花费的时间。

The developing driving part has a developing roller gear formed on a developing roller shaft.

显影驱动部件具有形成在显影辊轴上的显影辊齿轮。

In the case of rotating a business card printing and membership card production after roller gear change ink position, the gear must not, and, if you want to change the rotation business card printing and membership card making roller gear, where there is no ink, ink is made up of nano-imprint lithography drum or delivery caused by 5.1 gear.

如不静弹某个制卡和会员卡制息滚筒上的齿轮后不朱杠场所有保持，则该齿轮必不退不成，给调换；如不静弹制卡和会员卡制息滚筒上的齿轮，不朱杠场所均不有有保持，则不朱杠是由压印滚筒或播纸滚筒上的齿轮引起的了。

The problem of how to correct the profiles of roller gear cam is studied.The function of CMM is studied according to the CMM that is owned by Engineering training center. A method of using CMM to measure surface error of roller gear cam is researched.

结合工程训练中心现有的三坐标测量机设备，仔细研究了三坐标测量机所能实现的测量功能，提出了一种用三坐标测量机测量弧面分度凸轮轮廓面误差的方法。

Normal plant production, have fixed customers (Zhangjiagang, Jiangsu Guotai International Group), etc., well-equipped: spinning a gill box, B465A Roving Machine (6 into a new, normal activities), three new computer inverter control roller flower Twisting Machine type two simple machine is not only easy to adjust and make the roller continuously variable, and can set a variety of flower-type random combinations of process parameters.

工厂目前正常生产中，有固定客户（江苏张家港国泰国际集团）等，设备齐全：前纺针梳机一套、B465A粗纱机（6成新、正常活动中）、新式电脑变频控制三罗拉花式捻线机两台（操作简易，不仅便于机台的调整，并且使各罗拉无级变速，而且可以随机设定各种花型组合工艺参数。

In order to deeply reveal the smoothing mechanism of roller burnishing and to overcome the difficulty in the selection of the burnishing cross feed dependent mainly upon experiences and hand feel, the roller burnishing process is taken as an issue of plane-strain mechanics and the micro-plastic deformation area is determined on the basis of the Von-Mises yield criterion and by using the Boussinesq-Flamant solution. Then, the contact pressure distribution is obtained based on the Hertz contact theory, and the stress distributions in the burnishing tool and the workpiece are respectively revealed.

为深入了解滚柱滚压表面光整机理，解决目前滚压量选择完全凭经验和手感的不足，将滚柱滚压加工过程视为平面应变力学情形，利用Boussinesq-Flamant问题的求解并根据Von-Mises屈服准则得出了滚压局部发生微塑性变形的区域，根据Hertz接触理论得出了滚压接触压力分布及滚压过程中工件和工具的应力分布。

Roller batteries fig 10, these print by means of the ink fountain, the conveyor rollers, brayers ,inkers, printing plate holder and central roller bearing the rubber stamp.

辊筒组件，由墨斗、传动辊、传墨辊、墨辊、印版辊筒、橡皮辊共同完成印刷动作。

The results shows that the ceramic roller can meet the production requirement instead of cast iron roller.

结果表明，将原有的铸铁辊道改为陶瓷辊道能够满足生产的要求。

All kinds of cast iron rolls, centrifugal roller, steel roller and semi-steel rolls, alloy steel high-temperature wear-resistant steel.

各类铸铁辊、离心辊、钢辊及半钢辊、合金耐磨钢耐高温钢。

When passing water roll manual pressure chinsang water roller test pressure, the pressure to find a bigger point, and they are being built by chromeplating hard iron roller, too much stress borne water roll like a frame on the same series water rolls, resulting in a biography of the shaft and water roll and bucket motor drive gear does not match the space is large, it will be some operation.

当把传水辊手不静压上串水辊尝试不张力时，发掘两者之间的不张力不小了不面，而它们都是经过镀铬的软铁辊，过不小的不张力会使传水辊像架在串水辊上不同，导致传水辊轴脚与水斗电机传不静齿轮不匹配，间隙较不小，运转时不离会有些颤不静。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。