查询词典 roll-over

Product description: ZT4-00 23 liters laboratory beater Characteristic: This machine adopts Holland type beater chest, beater roll, bed knife which all used high-quality stainless steel; beater roll is made of stainless steel, knife can't be drop. Long performance life; automatically beat time control; dustcoat used organic material transparent high strength, whole operating process is directly observed.

产品说明： ZT4-00型23升打浆机特点：本机采用荷兰式浆池、飞刀辊、底刀并全部采用优质不锈钢制作；其中飞刀辊是整体不锈钢制作，不存在刀片松动等现象，使用寿命长；打浆时间自动控制；外罩采用透明高强度有机材料制作，整个操作过程直观可视。

A series of flexible U sections,changed in its sections,was separately simulated and analyzed by edger roll forming and flat roll forming.

本文对变截面辊弯成型仿真采用轧辊轴向加工技术，对角度连续变化的变截面U型材分别进行立辊加工和平辊加工成型模拟分析。

Roll a bucket to electroplate generally, roll a bucket inside of the work piece

一般的滚桶电镀，滚桶内的工件是随着滚桶的转动而翻动。

Film or paper surface dirty, and wrapped it into the dust or clear plastic mulch films after the crease or relaxation phenomena, film hemming switched to a new membrane drying temperature is too high, adhesive surface crust adjust oven temperature, clear crusts partⅱ thermotolerance cohesion and not enough use better glue wrinkle of polymer-coated film transfer after the roll is not the proper balance of films at both ends are inconsistent or wave; adjustment layer of polymer-coated machine too thick, solvent evaporation incomplete, viscosity, pressure drum extrusion, paper (Business card printing and membership card making products) and films between slide to adjust the film covering technology electrothermic roll and rubber roller ends is not plain, pressure is inconsistent, ranging from the adjustment of the linear speed of the machine after the temperature inside the plastic mulch film covering the subject in yellow glue resin particularly resin or additives not resistant to ageing, in the light, heat, under the influence of ultraviolet radiation, chemical change, build the pigments should be switched to a new glue

薄膜或纸张表面不干净，裹入灰尘或杂质清除后再行覆膜薄膜有折皱或松驰现象，薄膜卷边换用新膜干燥温度过高，粘合剂表面结皮调整烘道温度，清除结皮胶的粘接力和耐热性不够换用更好的胶水覆膜后起皱薄膜传送辊是否不平衡；薄膜两端松紧不一致或波浪边；调整覆膜机器胶层过厚，溶剂蒸发不彻底，影响了粘度，受压力滚筒挤压，纸张与薄膜之间产生滑动调整覆膜工艺电热辊与橡胶辊两端不平、压力不一致、线速度不等调整覆膜机器覆膜后易变黄胶水中的主体树脂特别是一些增粘树脂或助剂不耐老化，在光、热、紫外线的影响下，发生化学变化，生成有色物质应换用新胶水

The physical model and mathematics are established in which the coupled influences with other systems and the ellipticity of roll, the diameter deviation of roll, and mechanical gap are considered.

针对电力拖动子系统本身的特点，本文对主提升子系统和电力拖动子系统之间的耦合进行了处理，即将电力拖动的输出转矩作为阶跃激励施加在主提升系统上。

The result indicates that the ratio of roll diameter has the most important effect on the end curl,the angle of entrance is in the second place,the roll rotational velocity has the weakest effect.

正交实验是L25(45)，研究表明：辊径比对头部翘曲影响最大，导入角的影响次之，轧辊转速的影响最小，各种因素的影响趋势变化呈现了不同的规律。

The cross experiment was designed with L25 (4^5) The result indicates that the ratio of roll diameter has the most important effect on the end curl, the angle of entrance is in the second place, the roll rotational velocity has the weakest effect.

正交实验是L25 (4^5)，研究表明：辊径比对头部翘曲影响最大，导入角的影响次之，轧辊转速的影响最小，各种因素的影响趋势变化呈现了不同的规律。

The best technology parameters of rolling 6 mm Pb for experiment milli are 130/130 roll diameter, eduction 5%, angle of entrance -3°, roll rotational velocity 164 rpm.

实验轧机控轧6 mm铅板头部翘曲的最佳工艺参数为上下轧辊直径比1：1，压下率5%，导入角-3°，轧辊转速164 r/min。

FM improvements are that the Flanker now has a faster roll rate and the SFM was tweaked in roll rate for high IAS and high angle of attack.

FM的改进是，侧卫现在的滚转率更快，并微调了标准飞行模形使滚转率达到高IAS和高攻角

The calculation that the roll stress of taking strips and flection intensity of the roll shaft, and transmission gears.

计算带钢卷取过程中对卷筒的压力并计算卷取轴弯曲强度，对传动齿轮进行设计计算。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新