查询词典 roll-out

Keywords: Rolling bearing of mill; Micro dimensional behavior of roll system; Statically determinate roll system; Gyroscopic effect; Dynamic cross of rolls

中文关键词：轧机滚动轴承；辊系微尺度行为；静定辊系；陀螺效应；轧辊动态交叉

AThis machine adopt chain provide and double roller cycle roll , take carton piece though many working procedure of disport,roll line,cut horn,hit especial hole etc. it' ideal equipment of effect all processing carton piece working procedure one time.

本机采用链条送入、双辊轮转滚压的方式，将印刷好的箱片进行分纸、滚线、切角、打异型孔等多道工序，一次完成箱片的全部加工工序的理想设备。

On the roll-up door control exit passageway's fire protection roll-down metal door, should drop according to the following procedure automatic control: After feeling the smoke detector movement, curls the curtain to drop to is apart from the ground 1.8 meters; After feeling warm detector movement, curls the curtain to drop.

卷帘门控制疏散通道上的防火卷门，应按下列程序自动控制下降：感烟探测器动作后，卷帘下降至距地面1.8米；感温探测器动作后，卷帘下降到底。

Product description: ZT4-00 23 liters laboratory beater Characteristic: This machine adopts Holland type beater chest, beater roll, bed knife which all used high-quality stainless steel; beater roll is made of stainless steel, knife can't be drop. Long performance life; automatically beat time control; dustcoat used organic material transparent high strength, whole operating process is directly observed.

产品说明： ZT4-00型23升打浆机特点：本机采用荷兰式浆池、飞刀辊、底刀并全部采用优质不锈钢制作；其中飞刀辊是整体不锈钢制作，不存在刀片松动等现象，使用寿命长；打浆时间自动控制；外罩采用透明高强度有机材料制作，整个操作过程直观可视。

A series of flexible U sections,changed in its sections,was separately simulated and analyzed by edger roll forming and flat roll forming.

本文对变截面辊弯成型仿真采用轧辊轴向加工技术，对角度连续变化的变截面U型材分别进行立辊加工和平辊加工成型模拟分析。

Roll a bucket to electroplate generally, roll a bucket inside of the work piece

一般的滚桶电镀，滚桶内的工件是随着滚桶的转动而翻动。

Film or paper surface dirty, and wrapped it into the dust or clear plastic mulch films after the crease or relaxation phenomena, film hemming switched to a new membrane drying temperature is too high, adhesive surface crust adjust oven temperature, clear crusts partⅱ thermotolerance cohesion and not enough use better glue wrinkle of polymer-coated film transfer after the roll is not the proper balance of films at both ends are inconsistent or wave; adjustment layer of polymer-coated machine too thick, solvent evaporation incomplete, viscosity, pressure drum extrusion, paper (Business card printing and membership card making products) and films between slide to adjust the film covering technology electrothermic roll and rubber roller ends is not plain, pressure is inconsistent, ranging from the adjustment of the linear speed of the machine after the temperature inside the plastic mulch film covering the subject in yellow glue resin particularly resin or additives not resistant to ageing, in the light, heat, under the influence of ultraviolet radiation, chemical change, build the pigments should be switched to a new glue

薄膜或纸张表面不干净，裹入灰尘或杂质清除后再行覆膜薄膜有折皱或松驰现象，薄膜卷边换用新膜干燥温度过高，粘合剂表面结皮调整烘道温度，清除结皮胶的粘接力和耐热性不够换用更好的胶水覆膜后起皱薄膜传送辊是否不平衡；薄膜两端松紧不一致或波浪边；调整覆膜机器胶层过厚，溶剂蒸发不彻底，影响了粘度，受压力滚筒挤压，纸张与薄膜之间产生滑动调整覆膜工艺电热辊与橡胶辊两端不平、压力不一致、线速度不等调整覆膜机器覆膜后易变黄胶水中的主体树脂特别是一些增粘树脂或助剂不耐老化，在光、热、紫外线的影响下，发生化学变化，生成有色物质应换用新胶水

The physical model and mathematics are established in which the coupled influences with other systems and the ellipticity of roll, the diameter deviation of roll, and mechanical gap are considered.

针对电力拖动子系统本身的特点，本文对主提升子系统和电力拖动子系统之间的耦合进行了处理，即将电力拖动的输出转矩作为阶跃激励施加在主提升系统上。

The result indicates that the ratio of roll diameter has the most important effect on the end curl,the angle of entrance is in the second place,the roll rotational velocity has the weakest effect.

正交实验是L25(45)，研究表明：辊径比对头部翘曲影响最大，导入角的影响次之，轧辊转速的影响最小，各种因素的影响趋势变化呈现了不同的规律。

The cross experiment was designed with L25 (4^5) The result indicates that the ratio of roll diameter has the most important effect on the end curl, the angle of entrance is in the second place, the roll rotational velocity has the weakest effect.

正交实验是L25 (4^5)，研究表明：辊径比对头部翘曲影响最大，导入角的影响次之，轧辊转速的影响最小，各种因素的影响趋势变化呈现了不同的规律。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐