英语人>网络例句>roll-in 相关的网络例句
roll-in相关的网络例句

查询词典 roll-in

与 roll-in 相关的网络例句 [注:此内容来源于网络,仅供参考]

Through the computer simulation,analyzing the effects of pitch angle,roll angle,roll angle rate,sink rate,angle of attack and side angle on the track of ejection and save life height .

为提供弹射座椅多模态控制输入参数选择的理论依据,通过计算机仿真,比较分析了俯仰角、滚转角、滚转角速度、下沉率、迎角、侧滑角等弹射启动时飞机状态参数对弹射轨迹和安全救生高度的影响。

The Fuzzy-PID controller of fin stabilizer was designed based on fuzzy control and PID control theory. The controller of Fin Stabilizer is designed which uses roll angle and angular velocity of roll angel as input and fin angel as output. The model of ship is built based on Conolly theory. The controller is simulated using MATLAB. Results shows that compared with conventional PID controller, the FUZZY-PID controller has better effect.

设计了基于模糊控制和PID控制理论的FUZZY-PID复合控制减摇鳍控制系统,以横摇角和横摇角速度为输入量,鳍角为输出量,基于Conolly理论建立了船舶模型,利用MATLAB针对不同海情对控制器进行了仿真,结果表明减摇鳍模糊控制器动态响应性能和稳态控制精度均十分理想,能够满足减摇鳍控制系统的控制要求。

In the fast reversal, you use primarily aileron to roll with…in the high g reversal, you use a combination of aileron and rudder to roll with.

前一种反转主要利用副翼滚转,后一种则同时利用副翼和舵来完成反转。

There is no need a roll of film.

没有必要的胶卷。

I want to buy a roll of film for my camera.

我想要替我的照相机买一卷底片。

I thought we put a new roll of film in the camera before we left.

我认为我们提出一个新的轧辊的电影,在镜头前,我们离开。

I have a roll of film.

我有一卷底片。

I've got a roll of colored film.

我有一卷彩色胶卷。

I have got a roll of colored film.

我有一卷彩色胶卷。

I want a roll of 36 exposures of color film.

我想买一卷36张的彩色底片。

第30/341页 首页 < ... 26 27 28 29 30 31 32 33 34 ... > 尾页
相关中文对照歌词
Rock N' Roll
Tată (Father - Romanian Version)
Te-Am Visat
Roll With It
Rock N' Roll (Will Take You To The Mountain)
Rock N Rolla
Roll It
I'm On A Roll
That's The Way I Wanna Rock 'N' Roll
Roll Call
推荐网络例句

Based on the relationship and the phenomenon model, an improved model of MR damper has been presented in this paper.

摘 要:本文在实验数据的基础上建立了磁流变阻尼器输出力与不同常电流控制量的关系,对现有的 p模型进行了改进。

I don't think our founding fathers were very fuckable.

我认为我们的开国元老没什么吸引力

In chapter 3, an optimum method of milling parameter based on orthogonal cutting finite element model is proposed.

第三章提出了基于正交切削加工有限元模型的铣削参数优化方法。