查询词典 rod-shaped

Sitting on the reef and listening to the spoondrift, I suddenly felt my rod shaking. I raised the rod and a fish was caught.

坐在礁石上，听着海水溅起的声音，我的钓竿倏地抖动起来，竿起鱼现。

It cost only 10 yuan for renting the fishing rod. Sitting on the reef and listening to the spoondrift, I suddenly felt my rod shaking.

到了下午这时候我们已经是非常的累了，在房间里休息了一下，到了四点我们起床之后和很多人一样上了东极岛号游船，回舟山本岛。

It has mainly actions as follows: accumulating steel wire; sending steel wire; drawing steel wire; clipping; tighten; squeezing flat; regulating position of strapper, etc; using annealed rod of φ6.5,φ6.0 or hot-finished rod ofφ6.0 directly as strapping steel wire; it straps and tightens for 720°,and then squeezing flat to make sure that it straps firm and not easily loose.

它具有如下主要动作：蓄丝、送丝、抽丝、剪断、拧紧、挤平、打捆机位置调节等；使用φ6.5，φ6.0的退火盘条或直接采用φ6.0的热轧盘条作捆丝；其捆结拧紧720°，然后挤平，保证了捆结牢固，不易松脱。

Clean and check 1 slowly loosen the gland nut stuffing, packing the release of residual pressure of all components; 2 Remove all old packing, thoroughly clean axle / rod stuffing; 3 Check the shaft / bar have corrosion, dents, scratches or excessive wear; 4 Check whether there are other WATER POWER CONTROL VALVE parts burr, cracks, wear, they will reduce the packing life; 5 Check whether there is too much stuffing the gap, and the shaft / rod eccentric degree; 6 the replacement of defective parts larger; 7 Check the old packing, as BALANCING VALVES the basis of failure analysis to find the reasons for early failure of packing.

缓慢松开填料函的压盖螺母，释放盘根组件内所有的残余压力； 2）移去所有旧的盘根，彻底清洁轴/杆的填料函； 3）检查轴/杆是否有腐蚀、凹痕、划伤或过度磨损； 4）检查其他零件是否有毛刺、裂纹、磨损，它们会减少盘根的寿命； 5）检查填料函是否有过大的间隙，以及轴/杆的偏心程度； 6）更换有较大缺陷的零部件； 7）检查旧盘根，作为失效分析的依据，球阀以找到盘根早期失效的原因。

Finally, The manner of tension on prestressed steel rod and measure of tension is summarized concretely, with emphasis on the method of tension of steel rod by superelevation.

最后，对钢棒体系预应力施加方式进行了系统的总结，对具体张拉工艺也进行了分析，并重点对预起拱施加预应力这一方法作了详细介绍。

The internal boundary condition can be used to compute thin slab control rod worth in thermal research reactor. Internal boundary condition has been used to compute the control rod worth in JAERI's JRR-3M, and the results are compared with ones of JAERI.

对通过採用能量相关的內边界条件，在扩散理论的范围內计算薄板型热中子研究堆控制棒价值进行了理论分析，成功地计算了日本原子能研究所JRR-3M的控制棒价值，並与日本的计算结果进行了对比。

Press the spring-loaded rod inward to hold the ball in the mechanism, and tighten the thumbscrew to hold the rod in place.

向里按下加载弹簧杆，将小球固定在释放装置中，然后上紧拇指螺丝，将杆固定好。

NT40-type Power Cutter, ER-type Cutter, 0Z-type Cutter, side solid-type Cutter, flat milling toolholder, C-type, ER-type, 0Z-type tube clip, all kinds of Canadian long-rod, tool rod cutter, sugar hole devices, wrenches, etc..

NT40型强力刀头、ER型刀头、0Z型刀头、侧固式刀头、平面铣刀柄、C型、ER型、0Z型筒夹、各种加长杆、刀杆刀盘、搪孔器、板手等系列。

In consider drilling rod state, hole state, creep into course influence foundation of parameter synthetically, the drilling rodmodel under acting on the pulling force and torsion together carries on the theory to calculate, receive drillingrod pulling force and torsion differential equation group, in order to benefit drilling rod strength further to analyse.

在综合考虑钻杆状况、钻孔状况、钻进过程参数的影响基础上，对拉力和扭矩共同作用下的钻杆模型进行理论计算，得到钻杆拉力一扭矩微分方程组，以利于钻杆受力的进一步分析。

On the basis of the method of separating variables of sucker rod wave equation,in combination the matrix recursion technology with trigonometric series recursion technology,a kind of quick arithmetic of pump dynamograph in failure diagnosis technology of sucker rod pumping system is proposed.

在抽油杆柱波动方程分离变量法的基础上，将矩阵递推技术与三角级数递推技术相结合，提出了有杆抽油系统故障诊断技术中计算泵功图的一种快速算法，这种方法不仅适用于单级抽油杆采油系统，同时也适用于不同材质、不同杆径抽油杆组成的抽油系统。

According to the clear water experiment, aeration performance of the new equipment is good with high total oxygen transfer coefficient and oxygen utilization ratio.

曝气设备的动力效率在叶轮转速为120rpm～150rpm时取得最大值，此时氧利用率和充氧能力也具有较高值。

The environmental stability of that world - including its crushing pressures and icy darkness - means that some of its most famous inhabitants have survived for eons as evolutionary throwbacks, their bodies undergoing little change.

稳定的海底环境─包括能把人压扁的压力和冰冷的黑暗─意谓海底某些最知名的栖居生物已以演化返祖的样态活了万世，形体几无变化。