查询词典 ring in

Beautiful Ring Holder 14.99 - Beautiful ring holder is made from porcelain, is ivory colored, and adorned with dimensional roses.

美丽戒指持有14.99-美丽戒指持有瓷制成，象牙色、装维玫瑰。

Jump ring is an open 7mm jump ring.

跳圈是一个开放的7毫米跳圈。

Under function of impeller with high rotating speed, the used sand will be cast to the wearable junk ring to remove the inert film on su rface of the sand via mutual collision and friction between sand and junk ring, impeller and case of machine, sand and sand.

工作时旧砂在高速回转的叶轮作用下，抛向耐磨衬圈，通过砂粒与衬圈、叶轮与机盒、砂粒与砂粒之间的相互碰撞和摩擦，去除砂粒表面的树脂惰性膜。

Machine —— Gasket Cutting Machine, Common Spiral Machine, Numerical Control Spiral Maching Machine, No Core Spiral Making Machine, Metal ring rolling machine(make big size rings for spiral wond gasket), Metal Ring Notch Milling Machine spiral wound gasket rings kerve and angle

机器——垫片切割机，普通缠绕机，数控缠绕机，无芯模缠绕机，金属盘环机，金属环铣槽机，钢带成型机，垫片包边机☆盘根——膨胀石墨盘根碳化纤维盘根芳纶盘根碳纤维石墨盘根碳纤维四角，膨胀石墨混编盘根

In addition, it should be noted in swimming before the baby feed睡足, swimming is physical power, he is hungry will cry; Dai beach in the circle, we must note that some laps with long aging hard edge , your baby will cry uncomfortable wearing ring before hand to check all the inner ring; sometimes lap swimming wear well, because the baby will be uncomfortable而哭; temperature unsuitable he would cry.

此外，应该注意在游泳前让孩子吃饱、睡足，游泳很耗体力，他饿了也会哭的；在戴泳圈时也要注意，有的圈用久了边老化很硬，孩子不舒服也会哭，戴圈前请用手把内圈全部检查一遍；有时泳圈戴不好，孩子也会因为不舒服而哭；水温不合适他也会哭。

This is a popular rim with inclined and low profile, which is called "Lemmerz" rim Neither side ring nor locking ring is required on the assembling.

常用的斜低轮辋没有档图和锁圈，被称为Lemmerz 轮辋，应用于加强型轮胎中，如：林德叉车用轮胎轮辋等。

The locking ring also carries an indicator arrow and it is only when the indicator arrow is aligned, by turning the locking ring, with the indicator arrows and that the closure can be opened by lifting or flipping the projecting edge of the closure.

锁环也带有指示箭头，只有在通过旋动锁环使指示箭头与指示箭头对准时，才可通过抬起或翻转罩盖的突出边缘来开启罩盖。

Mainly thimble, reset rod, Secretary extinguishers (use of international standards such as the Japanese JIS, German DIN); SUJ2 derivative bearing steel columns, Introduction sets (using the Japanese "Fu Aventis" standard); jack mouth S45C high-quality steel products (use of international standards ), SKD11 Chong-pin, SKH51 straight needle, SUJ2 straight needle; there straight guide columns, occasional columns, sets of straight guide, care kits, gate kits rod guide column, bar ring, oblique derivative columns, quenching cylindrical, silver steel bars, flat die springs, black line round springs, high-speed steel Chong-pin, water Tsui, positioning ring, locking independent guide columns, sliding-oriented pieces, rolling-oriented pieces, heating tube , dual electric, high temperature wire, insulation casing, Nagarze wiring accessories such as mold.

主要有顶针、复位杆、司筒（采用国际标准如日本JIS、德国DIN）；SUJ2轴承钢导柱、导套（采用日本&富特巴&标准）；唧觜选用优质S45C钢材，SKD11冲针、SKH51直冲针、SUJ2直冲针；还有直导柱、托柱、直导套、托套、浇口套拉杆导柱、拉杆挡圈、斜导柱、淬火圆柱、银钢枝、模具扁弹簧、黑线圆弹簧、高速钢冲针、水咀、定位圈、锁扣独立导柱、滑动导向件、滚动导向件、加热管、电热偶、高温导线、绝缘套管、接线卡子等模具配件。

For locating bearing positions and CARB bearings insert a locating ring between the bearing outer ring and housing shoulder on the locknut side of bearing.

为将定位轴承和CARB轴承的位置定准，将一个定位环插放到轴承外圈和轴承座挡边之间、轴承锁紧螺母的一侧。

If the set weight need to be changed, you can control the lift weight according to the screw pillar's position in the 750-1000kg When adjust, loosen the locknut, every a ring going up, the set lifting weight can add 200kg, every a ring going down, the set lifting weight can reduce 200kg

4.2.3如需改变设定重量，可以在750-1000㎏范围以内，根据调整螺柱的位置不控制起升重量(调整时，先松开锁紧帽，调整每上行转一圈，原设定起重载重量增加200㎏，每下行转一圈原设定载重量减少200㎏，调整好后，用锁紧帽锁紧)。

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"