查询词典 ring bore
- 与 ring bore 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
It includes bore/outerside diameter deviation from basic, inner ring/outer ring width deviation in single radial plane.
几何精度包括内径偏差、平均内径差、外径偏差、平均外径差、套圈端面平行差的允许值。
-
In the axisymmetric section, the axial strain in excircle is maximum, but the maximum radial strain is in inner bore, and the radial strain contrast is used to reflect the variation trend of wall thickness in this ring section.
在轴对称截面的外圆上轴向拉应变最大,内孔处径向压应变最大,并用径向应变对比度来反映该环形截面壁厚的变化趋势。
-
Bearing bore or outside the surface and the ferrule end face connected to a ring surface.
轴承内孔或外表面与套圈一端面连接的套圈表面。
-
The valve plug is also available with a tungsten carbide tip and the seat ring can be fitted with a full-bore tungsten carbide insert for erosive service.
阀芯也可与碳化钨小费和座圈可以用全口径为糜烂性服务硬质合金插入装置。
-
Based on the theory of tribology and the wear characteristics of cylinder bore-piston ring, the regular micro geometric surface topography was honed on the cylinder bore using the technology of laser texturing.
基于摩擦学理论和缸套/活塞环的润滑磨损特征,采用激光微造型技术,在缸套内表面进行规则微观几何形貌的造型。
-
The ring bore a gold crest circled with "McColl High School" and "1940" divided on each side. That was my graduating year too.
那枚戒指有一个中学学校的饰章,四周围有'麦可尔中学'几个字,'1940'分刻在饰章的两边。
-
This tester evaluates seizure / wear characteristics and friction characteristics between piston and piston ring / bore, with conditions equivalent to the actual sliding motion of vehicle operation.
本试验台用于评价活塞和活塞环与发动机汽缸孔之间的摩擦磨损特性,可模拟实际车辆工作状态。
-
NSK uses the standard ISO clearance designations such as C2, Normal, C3, C4 and C5 for bearings with an inner ring bore diameter greater than or equal to 10mm.
恩斯克采用ISO标准的名称,如清除C2 ,正常,补体C3 , C4和C5的轴承内环钻孔直径大于或等于10毫米。
-
Revolving tolerance includes radial and axial runout of assembled bearing inner ring and outer ring, inner ring reference fcace runout with bore and outside cylindrical surface runout with outer reference face.
旋转精度是规定旋转时振摆的,包括内圈及外圈径向摆动和轴向摆动,内圈侧摆及外径面垂直度公差范围。
-
Check the worn situations of piston ring, cylinder bore, connection rod small end bushing and connection rod bore; replace them as necessary except for cylinder bore can be bored or add repair using cylinder liner
4.4.3检查活塞环、气缸孔、连杆小头衬套及连杆轴孔的磨损情况,必要时除气缸孔可镗孔或加修理用缸套外,其余则可更换
- 推荐网络例句
-
I didn't watch TV last night, because it .
昨晚我没有看电视,因为电视机坏了。
-
Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.
今年以来,在北京的很多小区里,电梯液晶电视被撤了下来。
-
I'm running my simile to an extreme.
我比喻得过头了。