查询词典 resistor

Solder the resistor lead along it's entire length for 1/4 or so along the trace leading away from the connector.

焊锡的电阻铅沿着它的整个长度为1/4或使沿线追查领导远离接头。

Wire resistive touch screen technology, the grass-roots to the voltage field in both directions through the precision resistor networks are added to the work of conductive glass surface, we can simply be understood as the voltage field in both directions of staggered working hours added to the same work surface, The outer layer of Ni-Au conductive layer is only just be used as a pure conductor, there are time-test, after touching the inner ITO contact point X-axis and Y-axis voltage value method measured touch point position.

五线电阻技术触摸屏的基层把两个方向的电压场通过精密电阻网络都加在玻璃的导电工作面上，我们可以简单的理解为两个方向的电压场分时工作加在同一工作面上，而外层镍金导电层只仅仅用来当作纯导电体，有触摸后分时检测内层ITO接触点X轴和Y轴电压值的方法测得触摸点的位置。

Wire resistive touch screen technology, the grass-roots to the voltage field in both directions through the precision resistor networks are added to the work of conductive glass surface, we can simply be understood as the voltage field in both directions of staggered working hours added to the same work surface, The outer layer of Ni-Au conductive layer is only just used as a pure conductor, there are time-test, after touching the inner ITO contact point X-axis and Y-axis voltage value method measured touch point position.

五线电阻技术触摸屏的基层把两个方向的电压场通过精密电阻网络都加在玻璃的导电工作面上，我们可以简单的理解为两个方向的电压场分时工作加在同一工作面上，而外层镍金导电层只仅仅用来当作纯导体，有触摸后分时检测内层ITO接触点X轴和Y轴电压值的方法测得触摸点的位置。

The resistor from when adds on the stipulation the load, the time which to has when fuse needs, is called the melting time, this performance, is called the fuse characteristic.

电阻器从加上规定的过负荷时，到发生熔断时所需的时间，称为熔断时间，这种性能，称为熔断特性。

Compared the calculated curve and the real assay curve we can make a conclusion that: this method can calculate the melting time of the fuse at the huge short current (more than 50 times of the current rating) with the error less than 5%; the resistor and time characteristic can also be acquired, it provided the date for overvoltage calculation of the fuse model. The research of the overvoltage during fusing process is based on short circuit test of the fuse.

由计算结果与实际试验曲线对比可得：该种方法能够比较准确地计算出较大短路电流下(熔断器额定电流的50倍以上)熔断器的弧前时间，误差一般在5%以内；同时还可以算得熔断器在弧前的电阻时间特性，为开断过电压仿真计算电路中的熔断器模型提供数据。

By the way,it may realize the change curve of negative temperature coefficient for the thermal resistor.

电压信号利用声卡采集到计算机中，由LabVIEW软件编写的虚拟锁相放大器测量，实现了测量负温度系数的热敏电阻阻值随温度的变化曲线。

This paper analyzes the hidden danger s in high voltage power supply of the ELA-120/6 electron beamwelding machine, and proposes two countermeasures:one is to redesign the fuel tank control circuit,but use operation regulations to solve the problems;another is install parallel connecting discharge resistor on high voltage capacitor.

分析了EAL-120/6型电子束焊机高压电源存在的安全隐患，提出了消除隐患的两种措施：一是不改动油箱电路，从操作规程上加以解决；二是给高压电容加装并联放电电阻支路。

Design as the master controller with AT89C51 one-chip computer this time, regard ADC0809 as the core, regard speed sensor, counter of the odometer, thermal resistor type sensor, pressure sensor as the main peripheral component, complement it with the essential peripheral circuit, has realized the design of the car instrument and realized, this instrument of systems have advantage such as being accurate, reliable, easy to use, have represented the newest development trend of the automobile-used instrument.

本次设计以AT89C51单片机为主控制器，以ADC0809为核心，以速度传感器、里程表计数器、热敏电阻式传感器、压力传感器为主要外围元件，辅以必要的外围电路，实现了仪表的设计与实现，该仪表系统具有准确、可靠、使用方便等优点，代表了车用仪表的最新发展趋势。

Connects resistor to VDD to generate speech or melody clock source.

电阻连接到VDD，以言语或旋律产生时钟源。

By shunt-wound method,we have made and calibrated a low-inductance sampling resistor.

采用电阻并联的方法，制作了小电感信号电阻。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。