查询词典 residual

Using the analysis of differential scanning calorimetry, three exothermic peaks were found which were mainly attributed to crystallization of α-(373℃), relaxation of internal strain (410℃) and crystallization of the residual amorphous matrix (540℃) respectively.

对机械合金化形成的非晶〓的DSC测量表明：在40℃到700℃范围内，有三个位于373℃，417℃和540℃左右的放热过程，分别α-相的结晶，内应变的降低和残余非晶相的晶化。

We choose an optimal model for functional mapping via comparing various combinations of submodels for mean vectors of QTL genotypes and residual covariance matrix according to statistical power of detecting QTL.

根据QTL的统计检测效率，通过比较关于QTL基因型的期望均值向量和剩余误差的协方差矩阵的子模型的不同组合，来筛选优化的功能定位模型。

On the basis of elastic mechanics theory, the residual microstress expression of matrix around fibers in composites and the stress distribution expression of the matrix around fibers in the composites during tensile process were deduced.

本实验中，纤维体积分数为15%和20%的复合材料强度分别在125℃和81℃时达到了基体的强度，而纤维体积分数为25%的复合材料在室温时强度就超过了基体的。

Modeling time-dependent expected mean vectors of QTL genotypes and the structure of the within-subject residual covariance matrix are the essence for functional mapping QTL of dynamic traits.

拟合与时间相关的QTL基因型的期望均值向量和剩余误差的协方差矩阵是动态性状功能定位的核心内容。

Optimal design of the incidence matrix for structured residual approach with maximized sensitivity is discussed in this paper, in order to overcome the shortcoming of SRAMS that ignores the speed and sensitivity of fault diagnosis while considering the isolability of fault codes in the incidence matrix design.

针对基于具有最大敏感性结构化残差的传感器故障检测与诊断方法在设计影响矩阵时只考虑故障编码的可分离性，而没有考虑故障诊断的快速性和灵敏性的缺点，给出了故障敏感度和故障诊断灵敏度等指标，并提出了两种影响矩阵的优化设计算法。

Ultramicrohardness testing was employed to measure the hardness of the matrix in a hotextruded SiCp/LD2 composite for characterizing the law of distribution of thermal residual strain in the matrix.

用超显微硬度仪测试了热挤出态的SiCp/LD2复合材料中基体微区的硬度，用于表征材料基体中的热残余应变分布规律。

Two kinds of thermal residual stresses exist in metal matrix composites. One of them is temperature gradient induced thermal stresses caused by temperature gradient in MMC. The other can develop upon cooling from the processing temperature to room temperature due to the coefficient of thermal expasion mismatch between the fiber and matrix and is called CTE mismatch induced thermal stresses.

金属基复合材料有两种形式的热应力，一种是在MMC中由于温度梯度引起的热应力，即温度梯度诱导的热应力；另一种是在冷却过程中由于基体金属和纤维的热膨胀系数不匹配引起的热应力，即热膨胀系数不匹配诱导的热应力。

We also elaborated upon the relations between immediately adjacent fibers and loadings、interfacial bonding、residual stress、matrix parameters and material elastic properties of two kinds of fibers and the influence on the observed"hybrid effect"in a hybrid composite.

计算了混杂复合材料由于高模量纤维破坏引起的高低模量纤维应力集中系数，详细分析了载荷大小、界面结合强度、残余应力和参与混杂的两种不同纤维及基体的弹性性质等与邻近纤维应力集中的关系及其对复合材料"混杂效应"的影响。

Besides univariate AR model, this dissertation finally presented our study on a parameter called the local spatiotemporal synchronization index, mainly based on residual covariance matrix of a multivariate autoregressive model.

除了单变数的自回归模型外，在这论文的最后，我们也提出了残余共变异矩阵，系根据多变数的自回归模型所发展出来的一个评估脑电波时空一致性的指标：LSTS（local spatiotemporal synchronization）指标。

This paper discusses a fast calculation method of GPS carrier phase integer ambiguity resolution, analyze independent variables in search space, derivate new residual transition matrix which directly associates all measurement error with minimum search space, and search space is minimized through selecting the ambiguity combination which is consistent with satellite geometry size and measurement error.

探讨了一种GPS载波相位整周模糊度的快速求解方法，分析了搜索空间中的独立变量，推导出了新的传递矩阵。该矩阵将所有的测量残差直接和最小求解搜索空间相关联，通过仅选择那些与卫星几何尺寸和测量残差一致的模糊度的组合，搜索空间被最小化。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐